BUSCH Mink MM 1324 AV Instruction Manual

BUSCH Mink MM 1324 AV

40 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Get technical data,

instruction manuals,

service kits

MINK

Claw Vacuum Pumps

MM 1324 AV, MM 1202 AV

MM 1252 AV, MM 1322 AV

Instruction Manual

0870133276 | B0007_en-US | Original instructions 2/23/2023

Table of Contents

Other manuals for BUSCH Mink MM 1324 AV

Installation And Operating Instructions56 pages

Questions and Answers:

J
joseph63Aug 23, 2025
What to do if my BUSCH Mink MM 1324 AV Water Pump won't start?
- A
  Adam RivasAug 23, 2025
  If your BUSCH Water Pump fails to start, begin by ensuring the drive motor is receiving the correct voltage. Next, check the drive motor starter overload protection; if it's set too low, compare its trip level to the nameplate data and correct if necessary, increasing it by 5 percent above the nominal drive motor current in high ambient temperatures. Also, verify that none of the fuses have blown. Finally, ensure the connection cable is adequately sized to prevent voltage drops at the pump.
S
Sherry GibsonAug 25, 2025
Why does my BUSCH Water Pump start, but labours or runs noisily?
- R
  Robert HaneyAug 25, 2025
  If your BUSCH Water Pump starts but is running with laboring sounds, unusual noises or rattling, check for loose connections in the drive motor terminal box, ensuring all wires are properly connected according to the connection diagram, especially on motors with six coils; tighten or replace any loose connections. For three-phase motor versions, verify the pump isn't running in the wrong direction. If foreign objects are present or bearings are stuck, it is best to have the vacuum pump repaired by Busch service.
Y
Yesenia KruegerAug 26, 2025
Why is my BUSCH Mink MM 1324 AV Water Pump running so hot?
- T
  Tony JohnsonAug 26, 2025
  If the BUSCH Water Pump is running very hot, first ensure sufficient air ventilation by cleaning the fan cowlings, fan wheels, ventilation grilles, and cooling fins to remove any dust or dirt impeding cooling. If the pump is in a narrow space, ensure adequate ventilation. Also, check that the ambient and inlet gas temperatures are within permitted limits.
S
Sharon JohnsonAug 27, 2025
Why is my BUSCH Mink MM 1324 AV so noisy?
- D
  Diana BennettAug 27, 2025
  If the BUSCH Water Pump is running very noisily, the issue could stem from defective bearings, which would require repair by Busch service. Another potential cause is a worn coupling element, which should be replaced. Low oil level or damage to the synchronizing gear can also cause noise, both of which necessitate repair by Busch service.
J
Jennifer RiceAug 29, 2025
What to do if BUSCH Water Pump or the drive motor is blocked?
- S
  Scott GarciaAug 29, 2025
  If the BUSCH Water Pump is blocked, ensure the drive motor is disconnected from the power supply. Remove the fan cover and try turning the drive motor with the vacuum pump by hand. If it remains frozen, remove the drive motor to check it and the vacuum pump separately. If the vacuum pump is blocked, it is best to have the vacuum pump repaired by Busch service.
S
sarah27Aug 30, 2025
What causes a BUSCH Mink MM 1324 AV Water Pump to be blocked?
- B
  Brandy CooperAug 30, 2025
  If your BUSCH Water Pump is blocked, it could be due to solid foreign matter entering the pump, requiring repair by Busch service; ensure the suction line has a screen, and consider adding a filter. Corrosion from remaining condensate can also cause blockage, necessitating repair by Busch service; check the process and consult the chapter on conveying condensable vapors. For three-phase motor versions, incorrect running direction can block the pump, requiring repair by Busch service; ensure correct direction upon connection.
S
Sharon GarciaSep 1, 2025
Why does the gas from my BUSCH Water Pump smell bad?
- E
  Ebony ShafferSep 1, 2025
  If the gas conveyed by the BUSCH Water Pump has a displeasing smell, it may be due to process components evaporating under vacuum. In this case, check the process itself to identify and address the source of the odor, if applicable.
J
Jessica MooreSep 2, 2025
What if the drive motor runs, but the BUSCH Mink MM 1324 AV Water Pump doesn't?
- A
  Andrea DorseySep 2, 2025
  If the drive motor of your BUSCH Water Pump is running, but the vacuum pump remains still, the coupling between the motor and pump is likely defective and needs to be replaced.
M
Michael DoyleSep 4, 2025
What to do if my BUSCH Mink MM 1324 AV Water Pump does not start?
- P
  priceianSep 4, 2025
  If your BUSCH Water Pump doesn't start, there could be several reasons: * The motor might not be getting the correct voltage. Check the power supply. * The motor itself could be defective, requiring replacement. * The coupling (CPL) might be defective and need to be replaced.
M
Mary WangSep 5, 2025
Why is my BUSCH Mink MM 1324 AV Water Pump running very noisily?
- D
  Destiny ClarkSep 5, 2025
  If your BUSCH Water Pump is running noisily, it could be due to: * A worn coupling (CPL), which requires replacement. * Low oil level. In this case you should top up the oil. * Defective bearings. It is recommended to contact Busch to repair the machine.

BUSCH Mink MM 1324 AV Specifications

General

Brand	BUSCH
Model	Mink MM 1324 AV
Category	Water Pump
Language	English

Related product manuals

BUSCH Mink MM 1322 AV

Preview: BUSCH Mink MM 1202 AV

BUSCH Mink MM 1202 AV

Preview: BUSCH Mink MM 1252 AV

BUSCH Mink MM 1252 AV

Preview: BUSCH MINK MM 1402 AV

BUSCH MINK MM 1402 AV

Preview: BUSCH MINK MM 1502 AV

BUSCH MINK MM 1502 AV

Preview: BUSCH MINK MM 1104 BV

BUSCH MINK MM 1104 BV

BUSCH MINK MM 1144 BV

BUSCH MINK MM 1102 BV

BUSCH MINK MM 1142 BV

Preview: BUSCH MINK MM 1104 CVM

BUSCH MINK MM 1104 CVM

Preview: BUSCH MINK

Preview: BUSCH MINK MV 0040 D

BUSCH MINK MV 0040 D