A
Anthony WiseAug 20, 2025
What to do if my BWT Water Dispenser unit regenerates at the wrong time?
- MMichael PattersonAug 21, 2025
Reset the present time and the regeneration time.
To Next PageTo Next PageWhat to do if my BWT Water Dispenser unit regenerates at the wrong time?
Reset the present time and the regeneration time.
How to reset regeneration time on BWT WS555?
To correct the regeneration time, reset the present time and then reset the regeneration time.
What to do if BWT WS555 Water Dispenser shows error code and audible alarm sounds?
If the BWT Water Dispenser's display shows error code "Err 1" and an audible alarm sounds, ensure all connections are secure. Turn the power off for 10 seconds, then turn it back on to allow the system to reset. If the display shows error code "SALt" and an audible alarm sounds, fill the brine cabinet with salt. Pressing the SET key will reset the salt alarm to the full capacity of salt. Also, verify that the power is on and all connections are secure.
How to fix BWT WS555 that regenerates at the wrong time?
If your BWT Water Dispenser regenerates at the wrong time, reset the present time.
What to do if the electronic display of my BWT WS555 shows an error?
If the electronic display shows an error, check that all the connections are secure, then turn the power back on and allow the system to reset. If the display shows the error code "SALt" and an audible alarm sounds, fill the brine cabinet with salt. Pressing the SET key will reset the salt alarm to the full capacity of salt. Also, ensure the power is on and all connections are secure.
What to do if water level in brine cabinet of BWT WS555 Water Dispenser reaches overflow?
First, verify that the line pressure is within the water softener's specifications by connecting a pressure gauge to a water outlet; the pressure should be between 1.7 and 5.0 bar. If the pressure falls outside this range, fit a pressure reducing valve or booster pump as needed. Also, check that the drain line isn't kinked, blocked, or frozen and that the power is on with secure connections.
Why is water running from the drain constantly in my BWT Water Dispenser?
If the unit is in recharge mode, this is normal; wait until the recharge is complete. If the unit is not in recharge mode, isolate the softener and call for service.
How to get water from BWT Water Dispenser?
Open the mains stop valve, and open the inlet and outlet valves to the water softener.
What to do if water still remains hard from BWT WS555 Water Dispenser?
Fill the brine cabinet with salt, switch the power on and check connections, close the by-pass valve and open the inlet and outlet valves, and reset the hardness if required.
What to do if the water level in brine cabinet reaches overflow in BWT WS555 Water Dispenser?
First, check if the line pressure is within the water softener's specification by connecting a pressure gauge to a water outlet; it should be between 1.7 - 5.0 bar. If the pressure falls outside this range, fit a pressure reducing valve or booster pump as required. Also, ensure the drain line is not kinked, blocked, or frozen and check that the power is on and the connections are secure.
General| Type | Water Dispenser |
|---|---|
| Model | WS555 |
| Brand | BWT |
| Hot Water | Yes |
| Cold Water | Yes |
| Room Temperature Water | Yes |
| Voltage | 220-240V |
| Frequency | 50/60Hz |
| Water Filtration | Yes |
| Capacity | 3.0 liters |
Safety guidelines for electrical connections and power supply.
Specifies the intended domestic use and liability disclaimer.
Warning against children playing with the appliance.
Important temperature limits for installation and operation.
Explains the working principle of a water softener using ion exchange.
Guidance on choosing a suitable location, considering space and weight.
Procedures for adding salt, salt level maintenance, and the low salt alarm.
Step-by-step guide to setting time, water hardness, and recharge time.
Procedure for manually initiating a regeneration cycle.
A checklist to diagnose and solve common water softener problems.
Detailed technical specifications for different BWT WS Range models.
