To Next PageTo Next PageWhat to do if water still remains hard from BWT Water Dispenser?
Fill the brine cabinet with salt, switch the power on and check connections, close the by-pass valve and open the inlet and outlet valves, and reset the hardness if required.
How to reduce excessive salt usage in BWT WS755 Water Dispenser?
If your BWT Water Dispenser is using excessive salt, reduce the hardness setting if it is incorrect.
Why does the water from my BWT Water Dispenser still remains hard?
If the water from your BWT Water Dispenser still remains hard, ensure that the brine cabinet is filled with salt. Also, switch the power on and check the connections. Make sure the by-pass valve is closed, and the inlet and outlet valves are open. If necessary, reset the hardness.
What to do if the water level in brine cabinet of BWT WS755 Water Dispenser reaches overflow?
If the water level in the brine cabinet of your BWT Water Dispenser reaches overflow, check the following: * Ensure the line pressure is within the specification (1.7 - 5.0 bar) by connecting a pressure gauge to a water outlet. * If the pressure falls outside this range, fit a pressure reducing valve or booster pump as needed. * Also, check that the drain line is not kinked, blocked, or frozen. * Finally, check that the power is on and the connections are secure, especially after a power interruption.
What to do if there is no water from BWT WS755 Water Dispenser?
First, open the mains stop valve. Then, open the inlet and outlet valves to the water softener.
What causes excessive salt usage in BWT Water Dispenser?
Excessive salt usage may be due to an incorrect hardness setting. Reduce the hardness if it is set too high.
Why does BWT Water Dispenser run from the drain constantly?
If the unit is in recharge mode, this is normal; wait until the recharge is complete. If it is not in recharge mode, isolate the softener and call for service.
How to fix hard water with BWT WS755 Water Dispenser?
To address hard water issues, start by filling the brine cabinet with salt. Then, switch the power on and check the connections. Ensure that the by-pass valve is closed and the inlet and outlet valves are open. Finally, reset the hardness setting if necessary.
What to do if the water level in brine cabinet reaches overflow in BWT WS755 Water Dispenser?
First, check if the line pressure is within the water softener's specification by connecting a pressure gauge to a water outlet; it should be between 1.7 - 5.0 bar. If the pressure falls outside this range, fit a pressure reducing valve or booster pump as required. Also, ensure the drain line is not kinked, blocked, or frozen and check that the power is on and the connections are secure.
What to do if my BWT WS755 Water Dispenser unit regenerates at the wrong time?
Reset the present time and the regeneration time.
Covers electrical safety, correct application, child safety, and temperature protection.
Advice on site selection, space, weight, and access for installation and maintenance.
Guide to setting the current time and inputting the measured water hardness level.
Procedure to define the automatic regeneration cycle's daily timing.
Resolving hard water issues by checking salt levels and power connections.
Troubleshooting steps for ensuring the softener is online and hardness settings are correct.
Diagnosing and resolving issues with no water supply or constant drain flow.
Addressing excessive salt usage, display errors, and incorrect regeneration timing.
Covers electrical safety, correct application, child safety, and temperature protection.
Advice on site selection, space, weight, and access for installation and maintenance.
Guide to setting the current time and inputting the measured water hardness level.
Procedure to define the automatic regeneration cycle's daily timing.
Resolving hard water issues by checking salt levels and power connections.
Troubleshooting steps for ensuring the softener is online and hardness settings are correct.
Diagnosing and resolving issues with no water supply or constant drain flow.
Addressing excessive salt usage, display errors, and incorrect regeneration timing.
General| Brand | BWT |
|---|---|
| Model | WS755 |
| Category | Water Dispenser |
| Language | English |
