Cadet 2F350 User Manual

cadetheat.com Tel: 360-693-2505 PO Box 1675 Vancouver, WA 98668-1675
Benets You Can Depend On
SAVE THESE INSTRUCTIONS
Electric Baseboard Heater
Owner’s Guide
6¾"
17.15cm
2½"
6.35cm
Side
Front
3¾"
9.53cm
3¾"
9.53cm
TOOLS REQUIRED:
• Phillips Screwdriver
• Straight Screwdriver
• Wire Strippers
• Drill or Hammer
• Drill Bits
• (4) Wood Screws
• Wire Connectors
• Strain Relief Connector
• Practical design is silent and built to last
• Easy installation with pre-punched
knockouts at 1-inch intervals
• Universal wiring available on either left or
right end
• Place under a window for convection to
naturally circulate warm air in your room
• Rest easy—includes high-temperature
safety shutoff feature
• Durable, powder-coated nish stands up to
nicks and scratches
• Your Cadet electric baseboard heater has
been thoroughly tested and is guaranteed
with a limited lifetime warranty
Electric Baseboard Models
Line
Voltage
Model Watts Amps
120
2F500-1 500 4.2
3F750-1 750 6.3
4F1000-1 1000 8.3
6F1500-1 1500 12.5
208
2F500-8 500 2.4
3F750-8 750 3.6
4F1000-8 1000 4.8
5F1250-8 1250 6.0
6F1500-8 1500 7.2
8F2000-8 2000 9.6
8F2500-8 2500 12
240
(1)
2F350 350 1.5
2F500 500 2.1
3F750 750 3.1
4F1000 1000 4.2
5F1250 1250 5.2
6F1500 1500 6.3
8F2000 2000 8.3
8F2500 2500 10.4
8F2025 2000/2500 8.3/10.4
10F2500 2500 10.4
(1)
240 volt models can be used at 208 volts. Wattage equals 75% of 240v rated
wattage.
http://www.cadetheat.com/products/baseboard-heaters/baseboard
Note: A wall thermostat or built-in thermostat kit is
required for comfortable warmth and control
Page 1

Cadet 2F350 Specifications

General

Brand	Cadet
Model	2F350
Category	Electric Heater
Language	English

Summary

Benefits You Can Depend On

Important Instructions

Thermostat Requirement

A thermostat is recommended for optimum performance or a built-in kit can be used.

Installation Placement Guidelines

Install heater under a window, along an outside wall, or near an outside door for best results.

Wiring Considerations

Wire connection is possible from either right or left side of the baseboard heater.

Voltage Importance

Verify electrical supply wires match heater voltage to prevent damage or reduced output.

Specific Model Wiring (8F2025)

Model 8F2025 is a multi-watt unit configurable for 2500 or 2000 watts.

Installation Instructions

Step 1: Mount Heater to Wall

Locate wall studs, remove wiring compartment cover, and install strain relief connector.

Step 2: Baseboard Wiring

Verify supply wires match heater voltage and connect wires according to diagrams.

Baseboard Wiring with a Wall Thermostat

Optional wiring instructions for single or double pole wall thermostats.

Multiple Baseboard Wiring

Optional instructions for wiring multiple heaters in parallel on the same circuit.

Operating Instructions

How to Operate Your Heater

Control room temperature using a wall or built-in thermostat for optimal comfort.

Maintaining Your Heater

Procedure for cleaning the heater element and cover every 24 months.

Troubleshooting Chart

Warranty