1
Setup Guide
Introductory Information
ENGLISH
QT6-1322-V01 PRINTED IN XXXXXXXXXXXXXXXX © CANON INC. 2016
Before setting up the printer, check the completed image of the printer you purchased and make sure you have enough space to install the printer.
It is recommended that you reserve space of the following dimensions to allow you to work around the printer.
Introduction
Read this manual before attempting to operate the printer.
Keep this manual in a handy location for future reference.
Set up the printer using the following procedure.
* Refer to the separate manual
* Refer to the separate manual
* Refer to the separate manual
• Windows is a trademark or registered trademark of Microsoft Corporation in the
U.S. and/or other countries.
PRO-2000
Installation space (W x D x H)
• When not using the stand
59.5 x 56.5 x 40.2 inches
(1510 x 1434 x 1020 mm)
• When using the stand
59.5 x 66.3 x 61.5 inches
(1510 x 1684 x 1560 mm)
PRO-4000
Installation space (W x D x H)
78.5 x 66.3 x 61.5 inches
(1993 x 1684 x 1560 mm)
PRO-4000S
Installation space (W x D x H)
78.5 x 66.3 x 61.5 inches
(1993 x 1684 x 1560 mm)
PRO-6000S
Installation space (W x D x H)
94.5 x 66.3 x 61.5 inches
(2399 x 1684 x 1560 mm)
Before Setting Up the Printer
Overview of Setup
• The printer stand and roll unit may be options depending on the model. Care is required because the required space may differ depending on whether or not the
options are used.
• The space required in front of the printer differs on how the basket supplied with the printer stand is used. This shows the installation space when used in the
position in the illustration.
• Instructions in this Setup Guide show the PRO-4000 printer. Note that your printer may look different from these illustrations in some cases. However,
the basic operations are the same.
• Some items are included with the printer but not described in
this manual.
Keep these items in a safe place after setup because they
are used invarious printing applications.
• For instructions on the included items not described in this
manual, refer to the Online Manual. ("How to Display the
Online Manuals" on p.14)
• A cable to connect the printer to a computer is not provided
with the printer.
RMC (Regulatory Model Code): K10441
RMC (Regulatory Model Code): K10440
RMC (Regulatory Model Code): K10439
RMC (Regulatory Model Code): K10438
If an error message appears during setup or other problems occur,
refer to "Responding to Messages" on p.14.
Assemble the Stand
(P.3)
(P.3)
Attach the Roll Unit
(P.4)
Attach the Basket
(P.4)
Turn On the Printer
(P.4)
Install the Ink Tanks
(P.6)
Install the Print Head
(P.8)
Load the Paper
(P.9)
(P.10)
(P.11)
Perform Print Head Adjustment and Select the Connection
Method on the PRO-2000
Select the Connection Method and Perform Print Head
Adjustment on the PRO-4000, PRO-4000S, and PRO-6000S
Connect to the Printer
(P.12)
Store Accessories in the Pockets
(P.13)
How to Display the Online
Manuals
(P.14)
Install the Printer
3.9 inches (100 mm)
5.9 inches (150 mm)
23.6 inches
(600 mm)
7.9 inches
(200 mm)
3.9 inches (100 mm)
5.9 inches (150 mm)
23.6 inches
7.9 inches
(200 mm)
3.9 inches
(100 mm)
(When not using
the stand)
23.6 inches
(600 mm)
(When not
using the stand)
23.6 inches
(600 mm)
(When using the stand)
3.9 inches (100 mm)
(When using the
stand)
5.9 inches (150 mm)
7.9 inches
(200 mm)
7.9 inches
(200 mm)
3.9 inches (100 mm)
5.9 inches (150 mm)
23.6 inches
(600 mm)
7.9 inches
(200 mm)
To Next Page
Need help?
General
