How to stop Bluetooth from automatically playing on my Canton Touch terminals?
If playback from a Bluetooth® device starts automatically when your Canton BRA 3 / VRA 3 Touch terminals are switched on, the automatic playback function Autoplay [APL] is activated (ON). Set the Autoplay [APL] function to OFF.
What to do if my Canton BRA 3 / VRA 3 Touch terminals remote control is not working?
If your Canton BRA 3 / VRA 3 Touch terminals aren't responding to the remote control, start by removing the protective film on the remote. If that doesn't work, replace the battery, ensuring correct polarity when inserting it.
How to fix no Bluetooth playback on Canton Spectral VRA 3 Touch terminals?
If you're experiencing no playback via Bluetooth® on your Canton BRA 3 / VRA 3 Touch terminals, ensure there is a connection between the device and the terminals. If paired but not playing, reconnect the device. Also, maximize the volume on the mobile device and increase the volume on the BRA 3 / VRA 3. Ensure that sources of interference, such as a WiFi router or a laptop, are not placed in close proximity to the BRA 3 / VRA 3. If you have simultaneous operation via WiFi and Bluetooth® connection from a mobile device, disable Wifi on the device. Finally, reduce the distance between the speaker and the mobile device, ensuring you are within the maximum range of 10 m.
Why is the sound so low on my Canton Touch terminals?
If the sound reproduction on your Canton BRA 3 / VRA 3 Touch terminals is too soft, first, increase the volume using the 'Volume' button and also increase the volume of the source device. If the maximum possible volume was limited by the 'Volume' function (VOL), increase the maximum possible volume according to instructions.
What to do if my Canton BRA 3 / VRA 3 Touch terminals won't turn on?
If your Canton BRA 3 / VRA 3 Touch terminals are not turning on, ensure the mains cable is properly connected to both the power outlet and the BRA 3 / VRA 3. Establish the connection if it is not.
Why doesn't my Canton BRA 3 / VRA 3 Touch terminals turn on automatically?
If your Canton BRA 3 / VRA 3 Touch terminals aren't turning on automatically, the standby function might be set to NSB, requiring manual power on. Switch the standby function to AUT. If the device was switched off via the 'ON / Standby' button of the remote control or the 'Power' button of the TV remote control (when using the IR learning function), switch on the BRA 3 / VRA 3 via the 'ON / Standby' button of the remote control and wait until it automatically switches to the standby mode next time. You can also delete the 'Power' button of your TV remote from the BRA 3 / VRA 3 to prevent it from switching off together with your TV. Also, ensure that the signal at AUX (Line) input is not too low; increase the output level on your source device.
Why don't my Canton wireless speakers turn on with the BRA 3 / VRA 3?
If coupled wireless speakers do not turn on together with the BRA 3 / VRA 3 Canton Touch terminals, the speakers may not be coupled together. Pair all slave speakers according to chapter WSP (Wireless Speaker Pairing). If the parameter Standby [STB] is set to ECO, each speaker must be switched on separately with the remote control. If you want to switch all speakers on together, set the parameter to NSB/ LAN, MAN or AUT.
Why can't I pair my Canton wireless speakers with my Touch terminals?
If coupling of wireless speakers fails with your Canton BRA 3 / VRA 3 Touch terminals, disconnect the slave speaker to be paired for at least 30 seconds from the mains. If the slave speaker was in standby mode during the pairing, after turning on the power switch of the slave speaker resp. connecting it to the mains, power it up by the remote control. If the slave was connected to the mains before the coupling was initialised on the BRA 3 / VRA 3 (master speaker), always start pairing at the BRA 3 / VRA 3 before connecting the slave to the mains. Finally, reduce the distance between BRA 3 / VRA 3 and slave speaker. The maximum distance is 10 m in the same room.
Why won't my Canton Spectral VRA 3 automatically switch to Bluetooth?
If your Canton BRA 3 / VRA 3 Touch terminals aren't automatically switching to the BT input, the BT Select function is likely deactivated (MAN). Activate the BTS function (AUT). Ensure that Bluetooth® is enabled on your device. If the BRA 3 / VRA 3 is connected to another device, disable Bluetooth® on the other device. If the device is not paired with the BRA 3 / VRA 3, pair your device with the BRA 3 / VRA 3.
Why does my Canton BRA 3 / VRA 3 Touch terminals turn on by itself?
If the Canton BRA 3 / VRA 3 Touch terminals unintentionally switches on, this can happen when your mobile device is playing system sounds such as when typing on the keyboard, a digital source is turned on, or an analog source is playing. Change the standby function from AUT to ECO, NSB, LAN or MAN.
General| Display | 15.6 inch PCAP Touchscreen |
|---|---|
| Processor | Intel Celeron J1900 |
| Internal Storage | 64GB SSD |
| Operating System | Windows 10 IoT Enterprise |
| Connectivity | Gigabit Ethernet, Wi-Fi 802.11 a/b/g/n, Bluetooth 4.0, 4 x USB 2.0, 2 x USB 3.0, 1 x Serial Port, 1 x Cash Drawer Port, 1 x HDMI |
| Dimensions | 390 x 250 x 360 mm |
| Weight | 5.8 kg |
To Next Page
