Cardiac Science Burdick 8500

Other manuals for Cardiac Science Burdick 8500

Product Safety Guide48 pages

Quick Steps2 pages

Questions and Answers

U
uedwardsAug 15, 2025
How to fix artifacts or noise on ECG trace with Cardiac Science Medical Equipment?
- S
  Steven GonzalezAug 15, 2025
  To minimize artifacts or noise on the ECG trace, try the following: * Prevent unnecessary patient movement. * Make sure all leads are clean, secure, and properly placed. * Ensure the skin is properly prepared and unbroken. * Verify all cables are securely connected. * Inspect cables for any damage like nicks, cuts, wear, or bulging. * Position the ECG device as far away as possible from other electronic equipment.
M
Miss Lauren WardAug 18, 2025
What to do if the AC power indicator is off on Cardiac Science Medical Equipment?
- B
  Benjamin MurphyAug 18, 2025
  If the AC power indicator (green LED on the back panel) is off, follow these steps: 1. Ensure both ends of the power cord are securely connected. 2. Check that the green LED on the external power supply is on. 3. Disconnect the ECG device from the external power supply to see if the external power supply LED turns on. 4. Confirm the power outlet is working. 5. Try replacing the power cord. 6. If the issue persists, replace the external power supply. 7. As a last resort, replace the power supply board.
L
Laura TerryAug 21, 2025
Why Cardiac Science Burdick 8500 won't operate when disconnected from AC power?
- A
  amber96Aug 21, 2025
  If your ECG device doesn't operate when disconnected from AC power or only operates briefly, consider these solutions: * Make sure the green LED on the external power supply is lit. * Verify the green power LED on the back panel is lit when charging the battery. * Confirm the battery is installed and the battery cable is securely connected. * Ensure the battery has been charged for at least four hours. * If the ECG device hasn't been used for several months, the battery might be fully discharged. Disconnect AC power and try charging the battery again.
C
Cory JacksonAug 25, 2025
What to do if Cardiac Science Medical Equipment unexpectedly reboots?
- J
  Joseph LeeAug 25, 2025
  If your ECG device unexpectedly reboots, try the following: * Ensure a battery is installed and check the green power LED on the back panel to verify AC power is available. * Adjust the brightness using Shift + Next or Shift + Previous. * Power off by pressing and holding the On/Standby key for 8 seconds, then restart the ECG device. * Make sure the keyboard cable and the display cable are securely connected. * If the problem continues, replace the top cover assembly, the power supply board, or the mainboard.
D
daviescodyAug 27, 2025
How to resolve 'Message Waiting for Data' on Cardiac Science Burdick 8500?
- C
  colemankatherineAug 27, 2025
  If you see a 'Message Waiting for Data' displayed, here’s what you can do: * Check the screen for a lead fail indication and fix that lead. * Inspect all the ECG leads. * Troubleshoot for noise, referring to the steps for 'Artifacts or noise on ECG trace'.
D
Debra HigginsAug 30, 2025
How to fix paper feed issue on Cardiac Science Burdick 8500?
- A
  Amy WatkinsAug 30, 2025
  If the paper does not feed, try these steps: 1. Select Setup. 2. Use the arrow keys (Next and Previous) to scroll to Service Functions and then press Select twice. 3. Select Printer Test Sequence. 4. Verify that the paper type in System Settings matches the installed paper. 5. Ensure you are using Burdick paper (Assurance® or Heartline™). 6. Check the paper door gear for damage and ensure the paper door is properly seated. 7. Remove and reinstall the paper, following the User’s Guide instructions. 8. Clean the queue sensor.
M
Meredith CastroSep 2, 2025
How to resolve communications errors on Cardiac Science Medical Equipment?
- B
  Beth HolmesSep 3, 2025
  To resolve communication errors, follow these steps: * Ensure the serial, phone, network, or USB cables are securely connected to the correct jack. * Check the communication settings. * For network problems, consult with the network administrator to ensure the destination is available. * Select Setup. * Use the arrow keys (Next and Previous) to scroll to Service Functions and then press Select twice. * Select Get IP Address.
J
Jacqueline BrownSep 5, 2025
What to do if there is no display on Cardiac Science Burdick 8500 Medical Equipment?
- D
  Diane EvansSep 5, 2025
  If there is no display, try the following: * Select Setup. * Use the arrow keys (Next and Previous) to scroll to Service Functions and then press Select twice. * Select Keyboard Test to verify keyboard operation. * If the On/Standby key doesn't work, make sure the battery is installed and check the green power LED on the back panel to verify AC power is available. * Restart the ECG device. * Clean the outside surface keyboard with isopropyl alcohol.
J
James HughesSep 8, 2025
How to fix inconsistent date and time on Cardiac Science Medical Equipment?
- K
  Kyle EdwardsSep 8, 2025
  To correct an inconsistent date and time, try replacing the 3V button cell on the mainboard. If that doesn't work, replace the mainboard assembly.
K
Kenneth HubbardSep 12, 2025
What to do if additional patients cannot be added to the patient directory on Cardiac Science Burdick 8500 Medical Equipment?
- M
  Michael StoutSep 12, 2025
  If you cannot add more patients to the directory, try printing or sending old records.

Summary

General Information

About the Burdick electrocardiographs

Overview of the Burdick electrocardiograph features and capabilities.

System description

Details the main subsystems of the Burdick ECG device.

Service & Maintenance

When to perform service procedures

Outlines service procedures and when they should be performed.

Functional checkout

Verifies normal operation. Includes calibration pulse check procedure on p11.

Electrical leakage current tests

Verifies electrical safety. Includes patient leakage and sink current tests on p12-13.

Queue sensor calibration

Calibrates queue sensor for paper feeding. Includes calibration procedure on p14.

Troubleshooting

Preliminary checks

Initial checks to perform before detailed troubleshooting.

Troubleshooting chart

Diagnoses and resolves common problems with solutions.

Component Replacement

Parts list

Lists device components and their locations.

Component replacement

Instructions for replacing components. Includes replacing top cover, paper drive, mainboard, power supply, and external power supply.

Disassembly

Procedures for disassembling components. Includes removing battery pack, keyboard, top cover, paper drive, mainboards, power supply board, and paper door.