9
Selecting the Horizontal Direction Louver Position
When the unit is turned on, the louvers default to the cooling or
heating position.
If the louver position is not providing adequate comfort due to
room layout or where people are gathered, two options are
available to correct the situation:
Setting the louvers in a stationary position
(other than default for heating and cooling):
The stationary position can be one of five (5) default positions or
a position selected by user.
To change the louver position, press the
“SWING“ button
once. The
icon is displayed on the remote.
OPER
º
F
º
C
HOUR
ON/OFF
:
A09640
When the is displayed, the louver will swing continuously
between positions 1 and 5 as shown below.
OFF
01 2 3 4
5678
A09634
If the “SWING” button is pushed again, the horizontal
louver will stop at the position it was in when the
button
was pressed. If position 1 through 5 is desired, push the
button repeatedly until the desired position (1 through 5) is
displayed on remote control.
Setting the lovers to move continuously:
This setting allows the louvers to move continuously between
either positions 1 through 5, or between positions 6, 7, and 8.
Push the
button once to have louvers swinging between
positions 1 and 5. If position 6, 7, or 8 is desired, push the
button repeatedly until the desired position is displayed on the
remote.
NOTE: Always use the remote control to adjust the horizontal
louver position otherwise, abnormal operation may occur. If
this occurs, turn the unit off and then on again.
Sometimes, in the heating mode, when the
”SWING”
button is pushed, the louvers will not start moving right away.
This is due to the fact that the fan will not start running until
the coil temperature is warm enough to prevent discomfort to
theuserbyblowingcoldair.
Selecting Vertical Direction of the Louver
The vertical louvers can be adjusted manually to direct the airflow
to achieve the optimal comfort in the space.
A07543
Timer Function
TIMER ON (to start the unit) and TIMER OFF (to stop the unit)
can be used separately or together. The clock on the remote control
must be set before using this function.
Timer ON only
º
F
º
C
HOUR
:
OPER
Only ON
is displayed.
ON
A09639
This function will allow the unit to start automatically at the set
time. The TIMER ON can be set while the unit is on or off.
To set the TIMER ON function, perform the following:
1. Push the “TIMER ON” button once.
2. The clock indicator
and time will not be displayed on
the remote control. The default “TIMER ON” time (first
time function is used) or the last time setting will be dis-
played and “ON” will flash.
3. Push the “--” or “+” within 5 seconds until the desired on
time is displayed.
NOTE: Pressing the “--” or “+” will decrease or increase the
time in 1 minute increments.
Pressing the “--” or “+” continuously will decrease or increase
the time in 10 minute increments.
4. Push the “TIMER ON” again. The “ON” icon will stop
blinking and the time at which the unit will start is set. The
clock indicator
and the time will be displayed again.
The “TIMER ON” time will be stored in memory indefinitely until
it is cancelled by the user by pushing the “TIMER ON” button or
the remote control batteries are replaced.
If the unit is running and the “TIMER ON” set time is reached, the
unit will continue operating normally.
NOTE: When the unit is shut off by the user using the
“ON/OFF” button, and if the “TIMER ON” is set, the
following will be displayed on the remote control.
-- Set Point
-- T i m e
-- Clock indicator
next to time indicates TIMER ON is set.
On the display panel, the operation light will turn red.
When the “TIMER ON” set time is reached, the display on the
remote does not change, but the unit will run as indicated by
the operation light on the front cover turning green. To get
display on the remote, push the “ON/OFF” button once.
To Next Page
Loading...
Need help?
General
