51-EN 52-EN 
– 26 –
EN
  Conrmation of indoor unit setup
Prior to delivery to the customer, check the address and setup of the indoor unit, which has been installed in this time and ll the check sheet (Table below).
Data of four units can be entered in this check sheet. Copy this sheet according to the No. of the indoor units. If the installed system is a group control system, 
use this sheet by entering each line system into each Installation Manual attached to the other indoor units.
REQUIREMENT
This check sheet is required for maintenance after installation. Fill this sheet and then pass this Installation Manual to the customers.
Indoor unit setup check sheet
Indoor unit Indoor unit Indoor unit Indoor unit
Room name Room name Room name Room name
Model Model Model Model
Check indoor unit address. (For check method, refer to APPLICABLE CONTROLS in this manual.)
* In case of a single system, it is unnecessary to enter the indoor address. (CODE NO.: Line [12], Indoor [13], Group [14], Central control [03])
Line Indoor Group Line Indoor Group Line Indoor Group Line Indoor Group
Central control address Central control address
Central control address Central control address
Various setup Various setup Various setup Various setup
Have you changed high ceiling setup? If not, ll check mark [×] in [NO CHANGE], and ll check mark [×] in [ITEM] if changed, respectively.
(For check method, refer to APPLICABLE CONTROLS in this manual.) * In case of replacement of jumper blocks on indoor microcomputer P.C. Board, 
setup is automatically changed.
High ceiling setup
(CODE No. [5d])
£
  NO CHANGE  [0000]
£
  STANDARD   [0001]
£
  HIGH CEILING 1   [0002]
£
  HIGH CEILING 3   [0003]
High ceiling setup
(CODE No. [5d])
£
  NO CHANGE  [0000]
£
  STANDARD   [0001]
£
  HIGH CEILING 1   [0002]
£
  HIGH CEILING 3   [0003]
High ceiling setup
(CODE No. [5d])
£
  NO CHANGE  [0000]
£
  STANDARD   [0001]
£
  HIGH CEILING 1   [0002]
£
  HIGH CEILING 3   [0003]
High ceiling setup
(CODE No. [5d])
£
  NO CHANGE  [0000]
£
  STANDARD   [0001]
£
  HIGH CEILING 1   [0002]
£
  HIGH CEILING 3   [0003]
Have you changed lighting time of lter sign? If not, ll check mark [×] in [NO CHANGE], and ll check mark [×] in [ITEM] if changed, respectively.
(For check method, refer to APPLICABLE CONTROLS in this manual.)
Filter sign lighting time
(CODE No. [01])
£
  NO CHANGE
£
  NONE   [0000]
£
  150H   [0001]
£
  2500H   [0002]
£
  5000H   [0003]
£
  10000H   [0004]
Filter sign lighting time
(CODE No. [01])
£
  NO CHANGE
£
  NONE   [0000]
£
  150H   [0001]
£
  2500H   [0002]
£
  5000H   [0003]
£
  10000H   [0004]
Filter sign lighting time
(CODE No. [01])
£
  NO CHANGE
£
  NONE   [0000]
£
  150H   [0001]
£
  2500H   [0002]
£
  5000H   [0003]
£
  10000H   [0004]
Filter sign lighting time
(CODE No. [01])
£
  NO CHANGE
£
  NONE   [0000]
£
  150H   [0001]
£
  2500H   [0002]
£
  5000H   [0003]
£
  10000H   [0004]
Have you changed detected temp. shift value? If not, ll check mark [×] in [NO CHANGE], and ll check mark [×] in [ITEM] if changed, respectively.
(For check method, refer to APPLICABLE CONTROLS in this manual.)
Detected temp, shift value setup 
(CODE NO. [06])
£
  NO CHANGE
£
  NO SHIFT  [0000]
£
  +1°C   [0001]
£
  +2°C   [0002]
£
  +3°C   [0003]
£
  +4°C   [0004]
£
  +5°C   [0005]
£
  +6°C [0006]
Detected temp, shift value setup 
(CODE NO. [06])
£
  NO CHANGE
£
  NO SHIFT  [0000]
£
  +1°C   [0001]
£
  +2°C   [0002]
£
  +3°C   [0003]
£
  +4°C   [0004]
£
  +5°C   [0005]
£
  +6°C [0006]
Detected temp, shift value setup 
(CODE NO. [06])
£
  NO CHANGE
£
  NO SHIFT  [0000]
£
  +1°C   [0001]
£
  +2°C   [0002]
£
  +3°C   [0003]
£
  +4°C   [0004]
£
  +5°C   [0005]
£
  +6°C [0006]
Detected temp, shift value setup 
(CODE NO. [06])
£
  NO CHANGE
£
  NO SHIFT  [0000]
£
  +1°C   [0001]
£
  +2°C   [0002]
£
  +3°C   [0003]
£
  +4°C   [0004]
£
  +5°C   [0005]
£
  +6°C [0006]
Incorporation of parts sold 
separately
Incorporation of parts sold 
separately
Incorporation of parts sold 
separately
Incorporation of parts sold 
separately
Have you incorporated the following parts sold separately? If incorporated, ll check mark [×] in each [ITEM].
(When incorporating, the setup change is necessary in some cases. For setup change method, refer to Installation Manual attached to each part sold 
separately.)
£
Others (                   )
£
Others (                   )
£
Others (                   )
£
Others (                   )
£
Others (                   )
£
Others (                   )
£
Others (                   )
£
Others (                   )
IM_1115350185.indb   26IM_1115350185.indb   26 26/6/2566 BE   14:5726/6/2566 BE   14:57