Need help?Do you have a question about the Carrier LENEL S2 and is the answer not in the manual?
General| Brand | Carrier |
|---|---|
| Model | LENEL S2 |
| Category | Locks |
| Type | Electromagnetic Lock |
| Voltage | 12/24 VDC |
| Lock Status Monitoring | Yes |
| Holding Force | 1200 lbs |
Specifies the operational frequency of the reader, which is 13.56 MHz.
Lists supported RFID and NFC technologies, including MIFARE and ISO 14443 A/B compatibility.
Details the SAM interface, which uses an external SIM card connection slot for enhanced security.
Outlines supported communication protocols like Wiegand, OSDP, RS232, and RS485.
Specifies the required power input range for the reader, typically 9 to 30 VDC.
Provides current draw specifications for idle and active modes, varying with voltage and heater status.
Describes the built-in tamper switch for detecting unauthorized opening or removal.
Defines the environmental operating temperature limits for the reader, from -40°C to +70°C.
Indicates the Ingress Protection rating, which is IP65/IK07 for dust and water resistance.
Details specifications for readers supporting both 13.56 MHz and 125 kHz operating frequencies.
Lists RFID technologies supported across both 13.56 MHz and 125 kHz bands.
Covers power supply requirements and current consumption details for dual-frequency readers.
Includes operating temperature, humidity, and IP rating for dual-frequency models.
Details specifications for readers supporting 13.56 MHz/125 kHz with SF/2F communication.
Lists supported technologies including MIFARE DESFire EV2/EV3 and iCLASS UID.
Specifies communication protocols like Wiegand, OSDP, and Supervised F2/F.
Covers power supply, current consumption, operating temperature, and IP rating.
Provides detailed current draw (idle and peak) for various reader models and configurations.
Explains heater functionality, activation conditions, and its impact on power consumption.
Lists all items included in the reader package, such as mounting plates, screws, and connectors.
Describes how to install and utilize the tamper alarm switch for break-off and opening protection.
Explains wiring for Wiegand and OSDP protocols, including pin assignments and cable requirements.
Provides important notes on cable length, shielding, and GPI/O usage for reliable connections.
Details wiring for Supervised F2/F communication, including pinouts and specific requirements.
Offers notes on cable specifications, GPI/O usage, and specific resistor requirements for F2/F connections.
Illustrates the wiring for 2-state Supervised F2/F readers, connecting exit buttons and door sensors.
Details wiring for 4-state Supervised F2/F readers, including resistor requirements for sensors.
Explains the steps to safely remove the front cover using a specific opening tool.
Describes how to enter programming mode using an authentication card and expected reader feedback.
Details the process of configuring the reader using a configuration card.
Explains how to update the authentication card used for setting the reader in programming mode.
Guides on how to reset OSDP secure channel encryption keys to installation mode.
Provides instructions on how to install the Secure Access Module (SAM) into its designated socket.
Details the stainless-steel spacer plate for ensuring tamper switch function on uneven surfaces.
Describes the standard distance plate for installations on uneven surfaces or with external wiring.
Explains the use of a large distance plate for covering installation holes or uneven surfaces.
Covers distance plates angled at 10 degrees to improve keypad accessibility and visibility.
Details 10° angled plates with specific mounting points for installation boxes and tamper functionality.
Describes a 33° angled plate designed for use with a QR code reader add-on module.
Presents technical specifications for the QR code reader module, including resolution and symbologies.
Details 33° angled plates for accessibility and visibility, suitable for speed gates or tabletop use.
Explains the vandal protection accessory that shields the reader from external forces.
Covers a combination accessory for external wiring and vandal protection.
Describes weather covers for climate and PIN privacy protection, enhancing IP rating.
Provides guidance on cleaning the reader using compressed air and isopropyl alcohol.
To Next Page