4. HOW TO USE ADVANCED FUNCTIONS
10
09
ECO
Sleep
Press ECO Sleep button under Auto/Cool/Heat mode
This Sleep operation saves energy and improves night time comfort by synchronising with the
body’s metabolism. The sleep function is not available in Fan or Dry mode.
ECO
Sleep
Swing
Press Swing button when the unit is turned on.
Swing
The horizontal louver will
swing up and down automatically
when pressing Swing button.
Press again to make it stop.
2s
Swing
Keep pressing this button more
than 2 seconds, the vertical louver
swing function is activated.
(Model dependent)
If continue to press the SWING button, five different airflow directions can be set. The louver can be move at a
certain range each time you press the button. Press the button until the direction you prefer is reached.
SET
or
SET
SET
OK
Press the SET button to enter the function setting, then press SET button or TEMP or TEMP
button to select the desired function. The selected symbol will flash on the display area, press the
OK button to confirm.
To cancel the selected function, just perform the same procedures as above.
Press the SET button to scroll through operation functions as follows:
FRESH function( ) (some units) :
AP function( )(some units) :
Follow me function( ) :
The FOLLOW ME function enables the remote control to measure the temperature at its current location
and send this signal to the air conditioner every 3 minutes interval. When using AUTO, COOL or HEAT
modes, measuring ambient temperature from the remote control(instead of from the indoor unit itself) will
enable the air conditioner to optimize the temperature around you and ensure maximum comfort.
When the FRESH function is initiated, the Ionizer/Plasma Dust Collector(depending
on models) is energized and will help to remove pollen and impurities from the air.
If the memory feature is stopped, “ ” displays for 3 seconds on the screen.
OF
While the memory feature is activated, press the ON/OFF button, shift the mode or power failure
will not cancel the Follow me function.
NOTE: Press and hold Turbo button for seven seconds to start/stop memory feature of Follow Me function.
If the memory feature is activated, “ ”
displays for 3 seconds on the screen.
On
Choose AP mode to do wireless network configuration. For some units, it doesn’t work by pressing
the SET button. To enter the AP mode, continuously press the LED button seven times in 10 seconds.
Fresh ( ) Sleep ( ) Follow Me( ) AP mode ( ) Fresh ....
[ ]: Model dependent
*
*
*
*
NOTE: If your remote controller has Sleep button, you can not use the SET
button to select the sleep feature.
Sleep function( )(some units) :
The SLEEP function is used to decrease energy use while you sleep(and don’t need
the same temperature settings to stay comfortable). This function can only be activated
via remote control. For the details, see “Sleep operation” in “USER’S MANUAL”.
NOTE:
The SLEEP function is not available in FAN and DRY mode.
X-ECO
Press this button under COOL Mode to enter the energy efficient mode.
Note:This function is only available under COOL mode.for heat pump air conditioner only.
Under cooling mode, press this button, the remote controller will adjust the temperature
automatically to 24 C, fan speed of Auto to save energy (only when the set temperature is
less than 24 C). If the set temperature is above 24 C, press the X-ECO button, the fan speed
will change to Auto, the set temperature will remain unchanged.
Note:
Pressing the X-ECO button, or modifying the mode or adjusting the set temperature to less
than 24 C will stop ECO operation.
Under ECO operation, the set tmeperature should be 24 C or above, it may result in insufficient
cooling. If you feel uncomfortable, just press the X-ECO button again to stop it.
O
O
O
O
O
The unit will enter the
energy efficient mode.
X-ECO
The SLEEP function is used to decrease
energy use while you sleep (and don’t
need the same temperature settings to
stay comfortable). Please refer to the
OWNER’S MANUAL for more details.
To Next Page
Loading...
