249
APPENDIX G — UPC OPEN CONTROLLER (CONT)
NETWORK POINTS LIST
POINT DESCRIPTION
CCN POINT
NAME
READ/
WRITE
UNITS
DEFAULT
VALUE
RANGE
BACNET
OBJECT ID
BACNET OBJECT
NAME
Air Temp Lvg Supply Fan R °F AV:10 sat_1
Airside Linkage Alarm R
0 = NORMAL
1 = ALARM
BV:7030 air_linkage_fail_1
Airside Linkage Status R
0 = Not Active
1 = Active
BV:2601 a_link_status_1
Alarm State R
0 = NORMAL
1 = ALARM
BV:9 alm_1
Building Pressure R H2O AV:1070 bldg_static_press_1
Building Pressure Setp. R/W H2O –0.25 to 0.25 AV:3070 bldg_press_stpt_1
Cir A Discharge Pressure R psig AV:1601 discharge_press_a_1
Cir A Sat. Condensing Temperature R °F AV:1602 sat_cond_temp_a_1
Cir A Sat. Suction Temperature R °F AV:1603 sat_suction_temp_a_1
Cir A Suction Pressure R psig AV:1600 suction_press_a_1
Cir B Discharge Pressure R psig AV:1605 discharge_press_b_1
Cir B Sat. Condensing Temperature R °F AV:1606 sat_cond_temp_b_1
Cir B Sat. Suction Temperature R °F AV:1607 sat_suction_temp_b_1
Cir B Suction Pressure R psig AV:1604 suction_press_b_1
Compressor A1 Relay R 0 = OFF; 1 = ON BV:16 cmpa1_1
Compressor A2 Relay R 0 = OFF; 1 = ON BV:17 cmpa2_1
Compressor A3 Relay R 0 = OFF; 1 = ON BV:13 cmpa3_1
Compressor B1 Relay R 0 = OFF; 1 = ON BV:18 cmpb1_1
Compressor B2 Relay R 0 = OFF; 1 = ON BV:19 cmpb2_1
Compressor B3 Relay R 0 = OFF; 1 = ON BV:14 cmpb3_1
Controlling Return Air Temp R/W °F –40 to 240 AV:1030 ra_temp_1
Controlling Space Temp R/W °F –40 to 240 AV:2007 space_temp_1
Controlling Static Pressure Setpoint R inH2O AV:3055 ct_sa_static_stpt_1
Cooling Control Point R °F AV:1024 cool_ctrl_point_1
Cooling Occupied Setpoint R/W °F 40 to 99 AV:3001 occ_cl_stpt_1
Cooling Unoccupied Setpoint R/W °F 40 to 110 AV:3003 unocc_cl_stpt_1
Ctl.Temp RAT,SPT or ZONE - Prime Variable R °F AV:43 ctrltemp_1
Current Running Capacity R % AV:1023 cool_capacity_1
Current Running Capacity (Heat) R % AV:44 htsg_cap_1
Dehumidify Cool Setpoint R/W °F 40 to 55 AV:49 dhcoolsp_1
Dehumidify Input R/W 0 = OFF; 1 = ON BV:30 dhdiscin_1
Dehumidify RH Setpoint R/W % 10 to 90 AV:50 dhrelhsp_1
Demand Limit Sw.1 Setpt. R/W % 0 to 100 AV:53 dlswsp1_1
Demand Limit Sw.2 Setpt. R/W % 0 to 100 AV:54 dlswsp2_1
Demand Limit Switch 1 R/W 0 = OFF; 1 = ON BV:1006 dmd_sw1_1
Demand Limit Switch 2 R/W 0 = OFF; 1 = ON BV:1007 dmd_sw2_1
Economizer Act. Curr. Pos R % AV:1028 econ_pos_1
Economizer Active? R 0 = NO; 1 = YES BV:36 ecactive_1
EDT Sensor Bad? R 0 = NO; 1 = YES BV:44 edt_stat_1
Element Comm Status
R
0 = No Comm
1 = Normal
BV:2999 element_stat_1
Element Communications Alarm R
0 = Comm Normal
1 = Comm Lost
BV:105 comm_lost_alm_1
Equipment Touch reset linkage Alarm R/W 0 = NO; 1 = YES BV:5123 et_reset_as_link_1
Evaporator Discharge Tmp R °F AV:76 edt_1
Exhaust Fan VFD Speed R % AV:2075 ef_vfd_output_1
Filter Status Input R/W 0 = CLEAN; 1 = DIRTY BV:1052 filter_status_1
Heat Relay 1 R 0 = OFF; 1 = ON BV:52 hs1_1
Heat Relay 2 R 0 = OFF; 1 = ON BV:53 hs2_1
Heat-Cool Setpoint Gap R/W °^F 2-10 AV:83 hcsp_gap_1
Heating Control Point R °F AV:1025 heat_ctrl_point_1
Heating Occupied Setpoint R/W °F 40 to 99 AV:3002 occ_ht_stpt_1
Heating Supply Air Setpt R/W °F 80 to 120 AV:3008 saspheat_1
Heating Unoccupied Setpoint R/W °F 40 to 99 AV:3004 unocc_ht_stpt_1
Ht.Coil Command Position R % AV:55 htclcpos_1
HumidiMizer 3-way Valve R 0 = OFF; 1 = ON BV:47 hum3wval_1
HumidiMizer Capacity R % AV:57 hmzrcapc_1
HVAC Mode Numerical Form R no unit AV:1022 hvac_mode_1
IAQ - Discrete Input R/W 0 = LOW; 1 = HIGH BV:1050 iaq_status_1
IAQ - PPM Return CO2 R/W no unit 0 to 5000 AV:1009 iaq_1
Indoor Air Quality R ppm AV:2607 link_iaq_1
Leaving Air Temperature R °F AV:1027 lvg_air_temperature_1
Linkage Max Damper Position R % AV:2611 link_max_dmpr_1
Local Schedule R 0 = OFF; 1 = ON BV:5 schedule_1
To Next Page
Loading...
