14
. Junction Access Control .
Every Extension can be programmed to access one or all of the 4 Junction Lines.
The access to each Extension can be different in Day mode and Night mode.
Procedure:
Dial #0000 + 70 J NNN X # (For Day Mode access)
Dial #0000 + 71 J NNN X # (For Night Mode access)
Where, J = 1, 2, 3, 4, 5, 6, 7 or 8 representing the 1
st
, 2
nd
, 3
rd
, 4
th
, 5
th
, 6
th
, 7
th
& 8
th
Junction Line.
NNN = Last 3 Digits of Extension Number
X = 0 to allow Junction access
1 to Disallow Junction access.
Dial #0000 + 70 J X # (To allow/disallow all extensions to access “J” Junction in Day Mode)
Dial #0000 + 71 J X # (To allow/disallow all extensions to access “J” Junction in Night Mode)
Dial #*0000 + 70 NNN X# (To allow/disallow all junction for NNN extension in Day Mode)
Dial #*0000 + 71 NNN X# (To allow/disallow all junction for NNN extension in Night Mode)
Default: All extensions are allowed to access all the 8 Junction Lines in both Day and Night mode.
. Junction Dialing Controls .
Junction dialing facility can be controlled Extension wise as below:
Dial #0000 + 40 NNN L #
where, NNN= Last 3 digits of Extension number.
L = 0 - The Extension can dial only the numbers starting with digits defined in “Allowed Table”
1 - The Extension can dial all numbers.
2 - The Extension can dial all numbers except for ISD numbers.
3 - The Extension can dial all numbers except for STD numbers.
4 - The Extension can dial all numbers except for the numbers starting with digits defined in “Denied
Table-A”
5 - The Extension can dial all numbers except for the numbers starting with digits defined in “Denied
Table-B”
6 - The Extension caNNNot dial out but can make internal calls.
To give all extensions the same L value: Dial #0000 + 40 L #
Note: In default: all extensions are in L = 1 mode.
. Junction Call Hold + Transfer + Making multiple calls .
To transfer a Junction line to another extension, FLASH and dial the Extension number while talking on the junction line.
Now there can be following 4 conditions:
1. When called extension lifts, calling extension can converse and then keep the Handset down. The Junction call will
then get transferred.
2. Called extension lifts but doesn’t want to talk then he may keep the Handset down.
The call will come back to the transferring extension.
3. The called extension is ringing but not lifting the Handset. Keep the Handset down.
The call will ring on the called extension for 25 secs and if not answered it will ring back on the transferring extension.
Now if the Transferring extension is busy, the Junction call will keep waiting for the Transferring extension to get free.
4. On dialing an engaged extension user would get engaged tone. During the engaged tone user can FLASH and get
Connected to the Junction line, This is the default setting in the PBX.
Alternately the user can change to the following mode: If the called Extension is engaged, the user will hear 2 tones.
Now FLASH from SLT/ Press HOLD key form KTS to get back to the Junction line. If FLASH from SLT/HOLD key is
not pressed form KTS is not done within 10 secs, the Junction line will get connected.
Programming: Dial #0000 + 830 #
To shift back to the default setting, Dial #0000 + 831 #
Making two or more Junction calls from SLT
While talking on one Junction line,
FLASH from SLT/ Press HOLD key form KTS
Dial ## - To park the call
Dial 0 to take another Junction
Dial the required Telephone number
FLASH from SLT/ Press HOLD key form KTS
Dial ## - To retrieve the first parked call
Similarly, more calls can be made.
To Next Page
Loading...
