7
Step1- Set SD_CARD play mode as auto attendant.
Step2- Set auto attendant mode for junction as multilayer1 or multilayer2.
Step3- Define UCD group if needed.
Step4- Program the key operation for level 1, level 2 and level 3.
For Multilayer Auto attendant-
Format SD-Card with FAT16/FAT32 format and make a folder named- 01
Put these files with File name in folder 01-
• 004-Multi layer AA msg1.mp3 (60secs)
• 005-Multi layer AA msg2.mp3 (60secs)
• 006-AA Level2 msg1.mp3 (23secs)
• 007-AA Level2 msg2.mp3 (23secs)
• 008-AA Level2 msg3.mp3 (23secs)
• 009-AA Level2 msg4.mp3 (23secs)
• 010-AA Level2 msg5.mp3 (23secs)
• 011-AA Level2 msg6.mp3 (23secs)
• 012-AA Level2 msg7.mp3 (23secs)
• 013-AA Level2 msg8.mp3 (23secs)
• 014-AA Level2 msg9.mp3 (23secs)
• 015-AA Level2 msg10.mp3 (23secs)
• 016-AA Level2 msg11.mp3 (23secs)
• 017-AA Level2 msg12.mp3 (23secs)
• 018-AA Level2 msg13.mp3 (23secs)
• 019-AA Level2 msg14.mp3 (23secs)
• 020-AA Level2 msg15.mp3 (23secs)
• 021-AA Level2 msg16.mp3 (23secs)
• 022-Night msg.mp3 (23secs)
Note- File name before - (dash) is fixed after that it can be any name and file extension must be .mp3
. Auto Day/Night Mode
Enable Auto Day/Night mode for particular day-
Dial- #* 0000 + 56 D X#
Where D= Day (1for Sun, 2 for Mon, …. 7 for Sat)
D= 0 for Enable/Disable for all days
X = 0 for Disable, 1 for enable
Setting time for Auto Day/Night mode-
Dial- #*0000 + 57 D A/P HH MN + A/P HH MN #
Where D= Day (1for Sun, 2 for Mon, …. 7 for Sat)
A/P – 0 for AM, 1 for PM
HH- Hour (01-12)
MN- Minute (00-59)
1
st
A/P HH MN is for Day mode time, 2
nd
A/P HH MN is for Night mode time.
. Barge-In .
Extension number 6001 and 6002 has the facility to barge into any Extension or Junction Line and over hear or talk in
conference.
#*0000+22 NNN# to add a Ext Number in barge in allowed table. (Maximum 5 extns) default is 6001,6002
#*0000+22# to reset it default 6001 and 6002.
To listen to a Junction line, dial # 7 J (J = 1 to 4, the Junction to be barged into)
To listen to an Extension, dial # 79 Ext Number
. Call Forward .
There are two types of Call Forwarding:
Call Forward Always
An extension can divert all incoming calls to another extension by dialing #81 XXXX from its own extension. Where XXXX
is the extension number where calls are to be diverted. XXXX can be 1-4 digits flexible number.
To clear this Call Forward Always feature: Dial #81#
This feature can also be programmed from any of the Programming Extensions as explained below:
To Next Page
Loading...
