DE
ES
FR
20
IT
EN
Notes:
- Pairing mode will last 2 minutes. BTEASY will switch
to standby mode automatically if it can’t pair with
any devices after 2 minutes. If you want to continue
to pair the BTEASY with a Bluetooth® device, please
turn off BTEASY first and try to re-pair according to
steps 1-6 mentioned above.
- BTEASY will turn off automatically when it can’t con-
nect to any devices after 5 minutes.
- BTEASY can remember 8 paired devices, when the
number of paired devices exceeds 8, the first one will
be replaced.
- When BTEASY is on but doesn’t connect to any
devices, press MFB button of BTEASY once, it will
connect to the last connected device automatically.
- Every time BTEASY is turned on, it will connect to
the last connected device automatically. If you want
to pair it with other devices, please turn off the cur-
rent device’s Bluetooth® function first and try to pair
BTEASY with the new device according to steps 1-6
mentioned above.
- When BTEASY gets out of working range of the con-
nected devices it will automatically reconnect to the
devices as soon as it is in working range again, either
it was connected to a interphone or a Bluetooth® cell
phone.
4. Intercom feature
If two interphones connect each other, you are able to
use intercom feature. Specific operations are as follows:
Function Operation or Status Indication tone
Receive intercom Ringing Ring
Send out
intercom
Press and hold VOL+
or VOL– for about 2
seconds, and release
it after hearing “DU”
tone
1 short tone
Cancel intercom
Short press MFB
button when
intercom is not put
through
1 short tone
Answer intercom
Short press MFB
button
1 short tone
Reject intercom
Press and hold MFB
button for about
2 seconds when
receiving intercom
1 short tone
End intercom
Short press MFB
button
1 short tone
5. Making calls with BTEASY
If BTEASY is connected to a Bluetooth® cell phone, now
you can make calls with BTEASY. The specific operations
are as follows:
Function Basic Operation Indication tone
Incoming ring Auto-ringing Ringing
Redial last number
Short press MFB
button twice
quickly
1 short tone
Cancel calling
Short press MFB
button when the
call is not put
through
1 short tone
Answer a call
Short press MFB
button
1 short tone
Reject a call
Long press MFB
button for 2 sec-
onds
1 short tone
End a call
Short press MFB
button
1 short tone
Volume up
Short or long press
VOL+ button
None
Volume down
Short or long press
VOL– button
None
Notes:
- When the volume is adjusted to max. or min. you will
hear two “DU” tones.
6. LED Indicator
a) When it is charging
LED indicator Status of BTEASY
Red LED is on Charging in progress
Red LED is off Charging finished
b) When it is not charging
LED indicator Status of BTEASY
Red and blue LEDs flash
alternately
Pairing mode
Blue LED flashes once every 3
seconds
Standby mode (not
connected)
Blue LED flashes twice quickly
every 4 seconds
Standby mode
(connected)
Blue LED flashes twice quickly
every 4 seconds
Incoming call/calling
Blue LED flashes slowly During a call
Red LED flashes Low power
CARE AND MAINTENANCE
Read the following recommendations before using
BTEASY. Following these you will be able to enjoy our
product for many years.
- Keep it dry and don’t take it to damp places to avoid
the product’s internal circuit being affected.
- Keep the product away from direct sunlight or hot
places. High temperatures will shorten the life of
electronic devices, destroy the battery or distort
certain plastic parts.
- Don’t expose the product to cold areas. It may dam-
age the internal circuit board.
- Don’t try to disassemble the product as it may get
damaged if you are not professional.
- Don’t let it fall down onto the floor or other hard
surfaces. The internal circuit might get damaged.
BTEASY BTEASY
To Next Page
Loading...
