Page 12 @+-*)/93='91<*A,/()'+=(B*4</1(/*91<<*CDEEEDE!!DF#"#6 Item 69724
GH@;IJ KL;MHINKO PHNOI;OHOQ;G;IRL
R(/-DP1'=)/=1=9/*N=()-,9)'+=(
*L-+9/>,-/(*=+)*(4/9'7'91<<]*/^4<1'=/>*'=*)3'(*:1=,1<*:,()*
0/*4/-7+-:/>*+=<]*0]*1*A,1<'7'/>*)/93='9'1=6
IK*LM;&;OI*G;MNKRG*NOZRMJ*@MKP*HQQNW;OIHV*KL;MHINKO2*
Q<+(/*1<<*&1<_/(B*>/)193*)3/*1'-*(,44<]B*(17/<]*>'(931-8/*1=]*-/('>,1<*1'-*4-/((,-/*'=*)3/*
)++<B*1=>*9<+(/*1<<*&1<_/(*181'=*0/7+-/*4/-7+-:'=8*1=]*4-+9/>,-/*'=*)3'(*(/9)'+=6
IK*LM;&;OI*G;MNKRG*NOZRMJ*@MKP*IKKV*@HNVRM;2*
W+*=+)*,(/*>1:18/>*/A,'4:/=)6**N7*10=+-:1<*=+'(/B*_'0-1)'+=B*
+-*</1['=8*1'-*+99,-(B*31_/*)3/*4-+0</:*9+--/9)/>*0/7+-/*7,-)3/-*,(/6
Q</1='=8B*P1'=)/=1=9/B*1=>*V,0-'91)'+=
O+)/2 These procedures are in addition to the regular checks and maintenance
explained as part of the regular operation of the air-operated tool.
1. U;@KM;*;HQY*RG;B inspect the general
condition of the Blaster. Check for:
• loose hardware or housing,
• misalignment or binding of moving parts,
• cracked or broken parts, and
• any other condition that may
affect its safe operation.
2. W1'<]*D*H'-*G,44<]*P1'=)/=1=9/2*
Every day, maintain the air supply according
to the component manufacturer’s instructions.
Drain the moisture filter regularly.
Performing routine air supply maintenance
will allow the tool to operate more safely
and will also reduce wear on the tool.
3. When re-using abrasive, sharp edges of abrasive
particles eventually become rounded and lose
cutting ability. At this point, replace the abrasive.
4. The parts of the tool that require frequent
wear inspection and occasional replacement
are those that carry the air/abrasive mixture.
Pay particular attention to the Abrasive Hose,
O-Ring, Abrasive Valve, Trigger Valve and
the Nozzles, as they will wear out much
more quickly than the other pieces.
QHRINKOc Air leaks in any of the above mentioned
parts need to be repaired before use.
5. H0-1('_/*Y+(/*'=(4/9)'+=2*
When new, the Abrasive Hose has 1/4″ ID.
The Abrasive Hose will need to be
replaced when its side walls develop
leaks or show blisters on the surface.
SHMONOTc**IK*LM;&;OI*G;MNKRG*NOZRMJ2**I3/*
H0-1('_/*Y+(/*9+,<>*31_/*-/('>,1<*10-1('_/*+-*
(,>>/=<]*0,-()6**L+'=)*)3/*O+aa</*'=*1*(17/*>'-/9)'+=*
1=>*./1-*1<<*(17/)]*8/1-*.3/=*>+'=8*)3'(*)/()6
a. Q<+(/*)3/*H'-*&1<_/B*H0-1('_/*&1<_/B*I3-+))</*
&1<_/B*)3/=*-/</1(/*)3/*I-'88/-*&1<_/6**I3/=*
9+==/9)*1=>*),-=*+=*)3/*1'-*(,44<]6
b. Adjust the air pressure to 60-125 PSI.
c. Open the Air Valve.
d. Open the Throttle Valve.
e. Then, run your fingers along the length
of the Abrasive Hose. An enlarged
spot (or bubble) indicates a weakened
section of the Abrasive Hose. W+*=+)*,(/*
)3/*U<1()/-*'7*)3'(*4-+0</:*'(*4-/(/=)*D*
-/4<19/*)3/*/=)'-/*H0-1('_/*Y+(/*7'-()6
6. To protect the compressor and its engine
or motor from damage by abrasive or dust
from abrasive blasting, keep the compressor
upwind of the Blaster or in a separate room.
7. W1'<]*D*H'-*G,44<]*P1'=)/=1=9/2*
Every day, maintain the air supply according
to the component manufacturer’s instructions.
Drain the moisture filter regularly.
Performing routine air supply maintenance
will allow the tool to operate more safely
and will also reduce wear on the tool.
To Next Page
Loading...
