CERUS Titan CI-030-P2 - User Manual

P Series
Fan & Pump Optimized
Variable Frequency Drive
0.5–40HP (200~230VAC) , 3Ø
0.5–700HP (380~480VAC), 3Ø
0.5-150HP (525~600VAC), 3Ø
Dual Rated for Constant & Variable Torque
Integrated PID Control
Application Based Commisioning
cerusind.com | 1.800.962.3787
Installation, Programming
Operation, & Maintenance
Manual
As with all electrical products, read manual thoroughly
before operating. Only qualied, expert personnel should
perform maintenance and installation. Contact the nearest
authorized service facility for examination, repair, or
adjustment. Do not disassemble or repair unit; death or
injury due to electrical shock or re hazard may result.
Product improvement is a continual process at Cerus
Industrial. Specications and manual data subject to
change. Consult factory for additional information.
CAUTION, SAFETY WARNING
I n t e l l i g e n t M o t o r C o n t r o l s
P Series Manual Fan & Pump Optimized Variable Frequency Drive
cerusind.com | 1.800.962.3787

Summary

Installation, Programming Operation, & Maintenance Manual

CAUTION, SAFETY WARNING

General safety warnings and precautions for operating electrical products.

SAFETY INSTRUCTIONS

Understanding Safety Symbols

Explanation of DANGER, WARNING, and CAUTION symbols used in the manual.

WARNINGS AND CAUTIONS

Specific Warnings

Precautions regarding VFD operation, wiring, and maintenance while power is applied.

PRECAUTIONS

Handling and Installation Precautions

Guidelines for safe handling, lifting, and installation of the VFD unit.

Wiring Precautions

Instructions for correct VFD wiring to prevent damage and ensure proper operation.

Start-up Procedures

Steps for safely powering up and checking VFD and motor operation.

CHAPTER 7 - PID CONTROL WIRING AND BLOCK DIAGRAM

PID Control Wiring and Diagrams

Wiring diagrams and block diagrams illustrating PID control setup.

CHAPTER 8 - TROUBLESHOOTING & MAINTENANCE

Fault Display and Remedies

Identifying and resolving VFD faults and error codes for maintenance.

8.1 Fault Display and Identification

List of VFD faults, protective functions, and their descriptions for troubleshooting.

VFD Power Component Checks

Procedures for testing VFD power components like diodes and IGBTs.

CHAPTER 3 - INSTALLATION AND WIRING

Installation Precautions

Essential precautions for VFD installation to ensure safety and proper operation.

3.2 Basic Wiring Diagrams

Power Wiring Diagrams

Diagrams showing power connections for various VFD models and terminal layouts.

3.2.6 Power Wiring Recommendations

Wiring Recommendations and Grounding

Essential guidelines for power wiring, including recommendations and grounding procedures.

CHAPTER 4 - OPERATION

VFD Programming Keypad Overview

Description of the LCD keypad, its layout, and dimensional drawing.

4.1.3 Programming the VFD Parameters

Navigating and Changing VFD Parameters

Step-by-step guide on how to program VFD parameters using the keypad.

4.2 Control Modes

Easy Start, Keypad, and Terminal Control Modes

Descriptions of different VFD control modes: Easy Start, Keypad, and Remote Terminal.

4.3 Function Settings and Descriptions

Application Selection and Parameter Settings

Overview of key parameter settings and their default values for different applications.

CHAPTER 5 - PARAMETER LIST

5.1 [SET] Setup Parameter Group

List and description of parameters in the SET group for application selection and basic settings.

5.3 [DRV] Drive Parameter Group

5.3 [DRV] Drive Parameter Group

List and description of parameters in the DRV group for step frequencies and monitoring.

5.5 [FG1] Function Group 1 Parameter Group

5.7 [FG2] Function Group 2 Parameter Group

5.9 [I;O] Inputs;Outputs Parameter Group

5.11 [APP] Application Parameter Group

CHAPTER 6 - PARAMETER DESCRIPTION

6.1 Setup Group [SET] - Application Selection

Description of SET-00 for selecting the VFD application and its impact on parameters.

6.3 Function Group 1 [FG1]

FG1 Jump Code and Acceleration;Deceleration Patterns

Parameters for navigating FG1 and setting acceleration/deceleration curves.

FG1 Pre-Heat and Start Mode Parameters

6.4 Function Group 2 [FG2]

FG2 Fault History and Timing Parameters

Parameters related to VFD fault history, trip times, and operational timers.

FG2 Jump Frequency and Flying Start

6.5 Input;Output Group [I;O]

I;O Jump Code and Analog Input Settings

Parameters for navigating I/O group and configuring analog voltage and current inputs.

Pulse Input Settings and Signal Loss Handling

6.6 Application Group [APP]

APP Jump Code and PID Feedback Settings

Parameters for navigating APP group and configuring PID feedback scaling.

Auxiliary Reference Modes and PID Control

6.8 Communication Group [COM]

COM Jump Code and Option Board Settings

Parameters for navigating COM group and configuring communication board types and modes.

MAC ID, Baud Rate, and Instance Settings

CHAPTER 7 - PID CONTROL WIRING AND BLOCK DIAGRAM

VFD Wiring for PID Control

Wiring diagram showing how to connect VFD for PID control with transducers.

PID Control Block Diagram

Block diagram illustrating PID control operation and parameters.

8.2 Fault Remedy

Troubleshooting Common Faults

Table detailing VFD faults, their causes, and recommended remedies.

8.3 Troubleshooting Conditions

Motor Starting and Speed Issues

Troubleshooting steps for common motor starting and speed control problems.

VFD Power Component Testing

CHAPTER 10 - MODBUS-RTU COMMUNICATION

10.1 Introduction to Modbus-RTU

Overview of Modbus-RTU communication for VFD control and monitoring.

10.2 Specification and Connection Guide

Warranty Information

In-Warranty and Out-of-Warranty Service

Details on warranty periods and conditions for service and repairs.

CERUS Titan CI-030-P2 Specifications

General

Brand	CERUS
Model	Titan CI-030-P2
Category	DC Drives
Language	English