CS35 2013.04
1.1.1-3 1.1.1-3General Information
2. Airbag - forbidden operations:
• Do not place the inflammable substance
or
gas g
enerato
r
t
ogethe
r with
the
air
bag.
• The storage temperature of gas
generator shall not exceed 80°C.
•
The airbag can n
o
t be re
versed.
•
D
o
not op
en the
gas genera
t
or ca
se.
• Do not place the gas generator near open
fire or heat source.
• Do not put any object on the airbag.
•
D
o
not use the
damaged a
i
rbag
.
• Do not touch the airbag and the gas
generator within ten min after they are
burnt.
•
D
o
not use the electr
icity meter prob
e on
the airbag circuit.
Air Conditioning Refrigerant
Refer to: Chemical Materials.
High
ly f
l
ammable - ob
serve No Smo
k
in
g policy
.
Skin contact may result in frostbite.
Instructions given by the manufacturer must be
followed.
A
v
oid
naked light
s, wear
suit
a
b
le
pro-
tective gloves and
goggles.
If refrigerant comes into contact with the skin or
eyes, imme
diate
l
y rinse the af
fe
cted
are
a
s with
water
.
Eyes should a
l
so
be
rinsed
with
an a
ppro-
priate irriga
tion
solutio
n
an
d should
not
be
rubbed. SEEK
MEDICAL ASSIST
ANCE IF NE
C-
ESSARY.
Air Conditioning Refrigerant- Do Nots:
•
D
o
not
expo
se re
frigera
n
t bo
ttles to
sunligh
t or hea
t.
• Do not stand refrigerant bottles upright,
wh
en
filling, hold them
with the valve
downwards.
• Do not expose refrigerant bottles to frost.
•
D
o
not dro
p
refrigerant
bottles.
•
D
o
no
t discharge
th
e
air conditioning
refrigerant in the atmosphere in any
circumstance.
•
Do
not use
the mixed refrigeran
t, such as
fluorine R12 and R134a.
Adh
esive and Sealant
Refer
to: Chemical Materials.
Hig
h
ly flammab
l
e - o
b
serve No Smo
k
in
g policy
.
Generally should be stored in No Smoking areas.
Cle
anliness
a
nd tidiness
in
u
s
e sho
u
ld be
ob
served, for
examp
l
e disposa
b
le p
a
per
cove
ring
benches, should be dispensed from applicators
where
possible,
con
t
ainers, including
se
cond
ary
cont
aine
rs, should be
labeled ap
propria
tely
.
1.
So
lve
n
t-based Adhe
sives/
Se
alers
Follow manufacturers instructions.
2. Water-based Adhesives/Sealers
T
hose
b
a
sed
on
p
o
lymer
emulsions
and
rub-
ber latexes may contain small amounts of vol-
a
t
ile
to
xic a
nd h
a
rmfu
l
chemicals. Skin
and
eye contact should be avoided and adequate
ventilation pro
v
id
ed during use.
3. Hot Melt Adhesives
I
n the
so
lid
st
ate,
they are
sa
fe. In
the
molten
state they may cause burns and health haz-
ards may arise from the inhalation of toxic
f
u
mes. Use
appro
p
riate
prote
c
tive cloth
i
ng
a
nd a the
r
most
a
t
ically con
t
rolled hea
ter with
a
thermal cut-ou
t and a
dequat
e ext
r
action.
4. Resin-based Adhesives/Sealers, for example
Epoxide and
Forma
ldeh
yde Resin-b
a
sed
Mixing should be carried
out in well ve
ntilated
areas, as harmful or toxic volatile chemicals
may be released.
Skin contact with uncured resins and harden-
ers can result in irritation, dermatitis, and
a
b
so
rption
of to
xic or
harmfu
l
chemica
l
s
t
h
rough
the skin
.
S
p
lash
es can d
a
mag
e
the
eye
s
. Provide
ade-
q
uate ventilation an
d avo
i
d skin and
eye con-
tact.
5. Anaerobic, Cyanoacrylate (super-glues) and
o
t
her Ac
rylic Adh
e
si
ves
Many
a
r
e irrit
ant, sensitizing or harmful to the
skin and re
spiratory tract. Some a
re eye
irri-
ta
n
t
s. Skin and eye
cont
act should be
av
oided and the
manu
factur
ers instru
ctio
ns
followed.
To Next Page
Loading...
