Chargestorm Connected

To Next Page





InstallationmanualChargestormConnected



1  Introduction

This document shows how to install and use the charge station Chargestorm Connected.

Figure 1 Chargestorm Connected

1) Front panel

2) Display with charging status symbols

3) Back cover

4) Technical box

5) EV connector (outlet or cable)

The manual is valid for the Chargestorm Connected family. Model information is found on the top of

the technical box. For a complete list of article numbers, please download datasheet at

http://www.chargestorm.se

2 Safety

ü Only accredited electrician is allowed to perform the installation described in this document

ü Read and follow the instructions in this document before installation and usage of the product

ü Installation must fulfill local safety regulations

3 Deliverycontent

Part of delivery

ü The charging station

ü Installation and user manual

ü Two keys

ü Cover for cable inlet (M32 and M12).

ü Holder for charging gun (In case charging station is equipped with fixed cable)

To bring

ü 4 pcs screws (M8) for wall mounting. Select screw type depending of wall.

ü 4 pcs of rubber seal/gaskets to use with screw. – Note very important!

ü RFID-tag (in case RFID shall be used) of type Mifare Classic/ IEC 14443 Type A. RFID-tags can

be ordered from Chargestorm web-shop (https://chargestorm.se/webbshop/)

Option

ü Pole mount kit for pole diameter 60 mm. Article number 920-00010.

Main Page

Need help?

Do you have a question about the Chargestorm Connected and is the answer not in the manual?

Summary

Introduction

Overview of Chargestorm Connected

Introduces the installation manual for the Chargestorm Connected.

Safety Precautions

Emphasizes electrician accreditation and following local safety regulations.

Delivery Contents and Required Items

Lists items included in delivery and tools/materials to bring for installation.

Optional Pole Mount Kit

Details an optional accessory for pole mounting the charging station.

Preconditions for Installation

Essential Tools for Installation

Lists necessary tools such as screwdrivers, multi-meter, and drilling machine.

Cable and Power Requirements

Specifies cable dimensions, power-off procedure, and cable length for installation.

Site Selection Criteria

Guides on choosing a suitable mounting location, considering space and environment.

Installation Procedure

Network Connectivity Requirements

Outlines prerequisites for 3G SIM card and Ethernet connection.

Unpacking and Initial Inspection

Step 1: Unpack the charging station and all its components from the box.

Wall Drilling and Preparation

Step 2: Determine mounting position and drill four holes in the wall.

Cable Entry Point Selection

Step 3: Decide if power and network cables enter from the top or bottom.

Wall Mounting the Unit

Step 4: Secure the charging station to the wall using appropriate screws.

Connecting Power and Network

Connecting Incoming Power Cable

Step 5: Peel wires, connect to terminal blocks, ensure ground wire is last.

Connecting Network and Testing

Step 6: Connect network cable and Step 7: Activate power and perform initial test.

Understanding Display Symbols

Explains the meaning of various LED indicators and symbols on the unit.

Provisioning and Configuration

Overview of Provisioning Process

Configuring the station for operational use via network and portal.

Accessing the Local Web Interface

Instructions to connect via USB and log in to the configuration interface.

Configuring Network Interface Settings

Steps to set up Ethernet or 3G for internet access.

Network Configuration Details

Ethernet Network Setup

Detailed steps for configuring IP settings for Ethernet connection.

3 G PPP Modem Setup

Instructions for configuring the 3G connection using PPP modem settings.

Advanced Provisioning

WWAN Modem Configuration

Steps to configure the robust 3G WWAN mode for the modem.

Setting Charging Current Limits

How to configure the maximum current limit for charging outlets.

Configuring Portal Server Access

Steps to connect the charging station to the backend portal.

Authentication and Portal Setup

Backend Portal Connection Details

Specific settings for the backend portal, including Chargebox ID and protocol.

RFID Authentication Configuration

Setting up RFID for user authentication before charging starts.

Product Information

Product Specifications

Details power, supply, fuses, mechanics, interfaces, and 3G option.

Compatibility and Safety

Covers standards, approvals, and safety features like ground fault detection.

Installation and Maintenance Tests

Preventive Maintenance Schedule

Recommendation for annual preventive maintenance of the charging station.

Required Installation Tests

Lists specific tests to be performed during installation.

Post-Installation Functional Checks

Verifying charging, software updates, and network access after installation.

Recycling and Warranty

Product Recycling Guidelines

Instructions on how to recycle the Chargestorm Connected unit.

Warranty Information

Details the warranty period for the Chargestorm Connected.

General Information and References

Document References

Lists related configuration and installation manuals.

Copyright and Contact Details

Provides copyright information and contact details for support.