Chicco KWIK.ONE - Maintenance

8
9
etc. Never leave the carrycot in the
vicinity of such heat sources.
• WARNING: Never use this product
on a stand.
• WARNING: Do not use the carrycot
to transport your child in the car.
• WARNING: If you purchase a
mattress separately to replace the
one supplied, make sure it ts the
product. The mattress must not be
thicker than 20 mm.
• WARNING: Do not add another
mattress on top of the mattress
supplied or recommended by the
manufacturer.
• WARNING: The carrycot must only
be assembled on the stroller in the
forward facing position.
• Check regularly the handles and
bottom of the carry cot in order
to notice any possible damage
or wear and tear. In particular, the
handles and the bottom of the car-
rycot. Should any damage or signs
of wear and tear be noticeable, do
not use the product and keep out
of reach of children.
• Before assembly, check that neither
the product nor any of its compo-
nents have been damaged during
transportation. In this case, do not
use and keep out of reach of children.
• Before lifting the carrycot to transport
your child make sure that the handle
is in the correct position for use.
• Do not attach any accessories not
supplied by the manufacturer. Any
unauthorised modifications made
to the product will relieve the man-
ufacturer of its responsibility.
• Do not leave anything inside the
carrycot that might reduce its
depth.
• This carrycot can only be used on
the CHICCO “KWIK.ONE” stroller.
• Make sure that the carrycot is cor-
rectly attached to the stroller be-
fore placing your child inside.
• Products exposed to direct sun-
light will heat up; allow them to
cool down before placing your
child inside.
• The carrycot is not designed for
children to sleep in for long periods
of time: this product is not a substi-
tute for a cot.
• Air the carrycot after prolonged use.
• In the carrycot your child’s head
must never be lower than their
body.
• Keep the product out of reach of
children when it is not being used.
TIPS FOR CLEANING AND MAINTENANCE
This product requires periodical maintenance. Cleaning
and maintenance operations must be performed exclu-
sively by an adult.
CLEANING
Clean the fabric parts using a wet sponge and neutral soap.
Periodically clean plastic parts with a damp cloth. To pre-
vent the formation of rust, always dry metal parts if they
have come into contact with water.
WASHING
The internal lining of the carrycot and the mattress are re-
movable and washable; to remove them, please refer to the
paragraph REMOVING THE CARRYCOT LINING.
Carefully follow the washing instructions on the label.
Below are the cleaning symbols and their meanings:
Wash by hand in cold water
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean
MAINTENANCE
To prevent the formation of rust, always dry metal parts. Do
not submerge the carrycot in water. Periodically clean plas-
tic parts with a damp cloth. To avoid friction, ensure that
the locking devices of the carrycot and stroller are free of
dust and sand. Do not leave the product exposed to the
sun for a long period of time; the fabrics may discolour. If
necessary, lubricate with dry silicone lubricant. Do not use
solvents or abrasive cleaning products.
The product includes a semi-rigid carrycot (with hood al-
ready assembled), an internal lining, a cover and a mattress.
FIRST ASSEMBLY OF THE CARRYCOT
1. To assemble the carrycot pull the “U”-shaped rod out-
wards using the strap (Fig. 1) until it is completely housed
in the slots on the wooden base (Fig. 1A). Repeat this op-
eration with the other rod.
WARNING: do not remove the protective parts from the
rods at the sides of the carrycot (Fig. 1B). Turn the lateral
joints of the carrycot to vertical position (Fig. 1C).
2. Insert the lining in the carrycot and x in place using the
special zips (Fig. 2).
3. Place the mattress on the base of the carrycot (Fig. 3).
4. Lift the carry handle (Fig. 4) checking that it is xed in the
vertical position.
Now the carrycot can be placed on a at and stable surface.
5. Using the zip, attach the cover to the carrycot (Fig. 5) and
pass the velcro straps through the fabric slots in the low-
er part of the hood (Fig. 5A). For added protection, lift
the fabric ap and x in place using the buttons on the
hood (Fig. 5B).
CARRY HANDLE
6. The carry handle can be completely lowered. To carry out
this operation pull up the two levers at the junction with
the hood at the same time (Fig. 6).
USING THE CARRYCOT AS A PRAM
This carrycot can be used as a pram by mounting it on the
KWIK.ONE stroller.
FASTENING THE CARRYCOT TO THE STROLLER
To attach the carrycot remove the bumper bar, close the
hood and completely lower the backrest, as shown in the
stroller instructions.
7. Hold the handle in transport position (Fig. 7) and attach
the carrycot to the fasteners at the side of the stroller with
the leg zone facing the handle of the stroller (Fig. 7A) until
it clicks into position.
WARNING: before using, make sure that the carrycot is
properly attached by pulling it upwards.
REMOVING THE CARRYCOT
8. Move the handle into the vertical position (transport po-
sition) until it clicks into place, press the buttons under
the hood junction (Fig. 8) and lift the carrycot from the
structure (Fig. 8A).
WARNING: The fastening and release operations can also
be carried out with your child in the carrycot; however, the
child’s weight may make these operations more dicult. Pay
attention when carrying out the aforementioned operations.
CLOSING THE CARRYCOT
It is possible to reduce the dimensions of the carrycot when
it is not being used. Lower the handle by pushing on the
30° C