Instruction manual: CITIZEN Eco-Drive Proximity
abc
2
Charging your watch
This watch has a rechargeable cell which is charged
by exposing the dial to light, such as direct
sunlight or fluorescent lamps (refer to page
2bc
for
charging guidelines).
After taking off the watch, put it in a location
where the dial is exposed to bright light, such as by
a window.
For optimal performance, be sure to:
• Expose the watch to direct sunlight half a day at least once a week.
• Avoid leaving the watch in dark places for long periods of time.
Caution
• Do not charge the watch at high temperature (about 60°C/140°F or higher).
• If the watch is obscured from light by long sleeves frequently, supplemental
charging may be needed to ensure continual operation. Refer to page
2bc
.
When the watch reaches a low charge state (insufficient charge warning
function)
When the power reserve becomes low, the second
hand moves once every two seconds. This is the
insufficient charge warning function. Be sure to
fully charge your watch as outlined on page
2bc
.
• When the watch is sufficiently charged, the
second hand will move normally.
• If you do not charge the watch for 10 days or
longer after the insufficient charge warning movement has begun,
the watch will be depleted of all power and stop.
Caution
• When in the insufficient charge warning state, the current time and date are
indicated. However, other features and functions of the watch will not be
available for use.
Charging time by environment
Below are the approximate times required for charging when exposing
the watch dial to light continuously. Please use this table as a reference
only.
*
Environment
Illuminance
(lx)
Charging time (approx.)
To work for
one day
To start working
normally when the
cell is discharged
To become fully
charged when the
cell is discharged
Outdoors
(sunny)
100,000
12 minutes 3.5 hours 13 hours
Outdoors
(cloudy)
10,000
30 minutes 6.5 hours 30 hours
20 cm (7-7/8
inches)
away from a
fluorescent
lamp (30W)
3,000
1.5 hours 15 hours 90 hours
Interior lighting 500
8 hours 80 hours 600 hours
1
2
4
5
6
7
8
3
Features
Connectable with your iPhone using Bluetooth4.0
through the dedicated app, and equipped with the
following features:
• Automatic Time Sync on page
6c
• Incoming Call Alert on page
6c
• Link Loss Alert on page
7a
• iPhone Search on page
7a
• Email Alert on page
7b
• Schedule Alert on page
7a
Eco-Drive (solar powered): Never needs a new battery. This watch is
fueled by light.
Chronograph: Measure elapsed time up to 60 minutes.
Local time: Easy to see the time for a second time zone, anywhere in
the world.
Perpetual calendar: Once set, the date will automatically adjust for
months shorter than 31 days as well as leap years.
* “Eco-Drive” is Citizen’s proprietary technology.
Component identification
1
Hour hand
2
Notification indication for connecting to iPhone (see page
5a
)
3
24-hour hand on the upper left sub dial
4
Second hand/Chronograph second hand
5
Function hand and function indications on the upper right sub dial
• Connection status (see page
5a
)/Power reserve level (see page
3a
)
• Chronograph minute hand
• Day of the week
6
Minute hand
7
Date indication
8
Mode hand on the lower sub dial (see page
3bc
)
The illustrations in this instruction manual may differ from the actual
appearance of your watch.
Upper right button ( )
Lower right button (
)
Crown
• To charge your watch, it is recommended to expose the dial to
direct sunlight. Optimal charging is achieved by exposing the dial to
direct sunlight outdoors for a short time each day.
Power reserve in normal use from fully charged without additional
charging
With connecting to iPhone Without connecting to iPhone
About 8 months
*
About 17 months
*
When the watch is connected to your iPhone about 6 hours a day and
received messages about 10 times a day, you can use the connecting feature
between the watch and your iPhone about 30 days in 8 months. For details,
see page
3a
.
Caution when connecting to iPhone
• Connecting to iPhone requires a substantial amount of power, especially if
receiving many notifications. Be sure to keep your watch fully charged when
utilizing this feature.
• We recommend disconnecting with iPhone when not needed (see page
6a
).
• Connecting feature does affect battery usage on your iPhone. Be sure to
check the charge level of your iPhone.
Power save function
If your watch is not exposed to light sufficient for charging for 30
minutes or more, the second hand will stop in order to conserve
power. Although the second hand is not moving, the correct seconds
are stored in memory.
The power save function cannot be activated manually; it is an
automatic feature only. The power save function does not operate
under the following conditions:
• The crown is in position
or .
• The current mode is Chronograph [
CHR
] or Calendar [
CAL
].
• The second hand is indicating a notification (“
MAIL
”/ “
CALL
”/ “
LL
”).
Canceling the power save function
The power save function is automatically canceled when the watch
is exposed to light sufficient for charging. The second hand will then
resume normal movement.
• The power save function will also be canceled if a notification is
received from your iPhone. Note: the watch must be sufficiently
charged and the dedicated app running on your iPhone in order to
receive notifications.
• If the watch is in the power save state for long period of time, adjust
the time and date before use through the iPhone connection (see
page
6c
) or manually (see page
8b
).
To Next Page
Loading...
