Clarion ARX6570z User Manual

16 ARX6570z
6. Press DISP button 0 to select a character.
Each time you press DISP button 0, the char-
acter changes in the following order:
Capital letters ➜ Small letters ➜ Numbers ➜
Symbols ➜ Capital letters...
7. Turn the Rotary knob % to select the desired
character. Turning the Rotary knob % clock-
wise moves the cursor to the next character;
turning it counterclockwise moves the cursor
to the previous character.
8. Repeat steps 5 to 7 to enter up to 10 charac-
ters for the title.
9. Press and hold ENT button 2 for 2 seconds
or longer to store the title into memory and
cancel title input mode.
Clearing titles
1. Play a CD in a CD changer or tune a radio
station or TV station that you want to clear
the title for.
2. Press DISP button 0 and display the sub-
title.
3. Press TITLE button 4. “TITL” appears in the
display and the display switches to the title
input display.
4. Press BND button @.
5. Press and hold ENT button 2 for 2 seconds
or longer to clear the title and cancel the title
input mode.
Message display
When the unit is powered on or off, a message is
displayed. The user can turn this message dis-
play on or off.
∗ The factory default setting is “ON”.
1. Press and hold ADJ button 4 for 1 second or
longer to switch to the adjustment selection
display.
2. Press the right or left side of SEARCH button
$ to select “MESSAGE”.
3. Press ENT button 2.
4. Turn the Rotary knob % clockwise to set the
message display to “ON”; turn it counterclock-
wise to set the message display to “OFF”.
5. Pressing ENT button 2 returns to the adjust-
ment selection display.
6. Press ADJ button 4 to return to the previous
mode.
Other Handy Functions
CD changer mode Number of titles
CDC655z connected 60 titles
CDC655Tz connected 100 titles
CDC1255z connected 50 titles
Mode Number of titles
Radio mode 30 titles
TV mode 15 titles
Setting the clock
1. Press and hold ADJ button 4 for 1 second or
longer to switch to the adjustment selection
display.
2. Press the right or left side of SEARCH button
$ to select “CLOCK”.
3. Press ENT button 2.
4. Press the right or left side of SEARCH button
$ to select the hour or the minute.
5. Turn the Rotary knob % clockwise or coun-
terclockwise to set the correct time.
∗ The clock is displayed in 12-hour format.
6. Press ENT button 2 to store the time into
memory.
7. Press ADJ button 4 to return to the previous
mode.
Note:
• You cannot set the clock when it is displayed with
only the ignition on. If you drain or remove the car’s
battery or take out this unit, the clock is reset.
While setting the clock, if another button or opera-
tion is selected, the clock set mode is canceled.
Entering titles
Titles up to 10 characters long can be stored in
memory and displayed for radio stations and
CDs. The numbers of titles that can be entered
for each mode are as follows.
1. Press FNC button 3 to select the mode you want
to enter a title (radio, CD changer or TV).
∗ Titles cannot be entered for MDs with this unit.
2. Select and play a CD in a CD changer or tune
to an appropriate TV or radio station.
3. Press DISP button 0 and display the sub-
title.
4. Press TITLE button 4. “TITL” appears in the
display and the cursor position flashes.
5. Press the right or left side of SEARCH button
$ to move the cursor.

Clarion ARX6570z Specifications

FM Tuner

frequency range	87.9 MHz to 107.9 MHz
usable sensitivity	11 dBf
50dB quieting sensitivity	17 dBf

AM Tuner

frequency range	530 kHz to 1710 kHz
usable sensitivity	25 µV

Tape Deck

wow & flutter	0.06%
channel separation (1 kHz)	45 dB
frequency response (120 µs normal)	30 Hz to 18 kHz

Audio

maximum power output	160 W (40 W × 4 ch)
continuous average power output	14 W × 4, into 4 Ω
bass control action (30 Hz)	±15 dB

General

power supply voltage	14.4 V DC (10.8 to 15.6 V allowable)
current consumption	Less than 15 A
weight / source unit	3.52 lb. (1.6 kg)