Sirius
Satellite
Radio
Operations
• "CALL 888"--?"539-SIRI"
: a channel not covered by your
contract
Call Sirius Service Center (1-
888-539-S1RIUS (7474)).
Online at siriusradio.com
Switching
the
display
1.
Press and hold the [DISPj button for 1
second or longer to select the sub display.
2.
In the sub display, press the [DISP] button to
cycle between the following display modes:
Channel name
~
title
~
artist
name
~
category
name
~
text
~
channel
name
~
...
Notes:
..
The
Operation status indication
of
the source unit
displays the abbreviated channel name for 2
seconds when
a station is selected before
returning
to
the previous display mode.
..
Scrolling starts when the channel name
or
other
text has been displayed for
2 seconds. When
scrolling finishes, the first text display appears.
To
start scrolling again, press
and
hold the
[MENU) button for
1 second
or
longer.
Channel
selection
Channels are selected with the following buttons.
• The
[~<llIII]
or
[.,.~]
button
• The [DIRECT] buttons
• The [CAT] button
"
For
details, see the following operation
descriptions.
Note:
..
The
audio output is muted
and
other button
operations are
not
accepted during channel
selection.
Tuning
There are 3 types of tuning mode available, seek
tuning, manual tuning and preset tuning.
Seek
tuning
Only channels that can be received are selected
while channels without broadcasts and channels
not covered by the contract are automatically
skipped.
1.
Press the
[~
....
] or
[.,.~]
button.
The receiver seeks the next available
channel below
or
above the current channel.
2.
Press and hold the
[~
....
] or
[.,.~]
button. I
The receiver moves to seek channels below •
or above the current channe1. If the channel
found when either button is released is
available that channel
is
received.
Otherwise, seeking continues until an
available channel is found.
Manual
tuning
Any channel including channels without
broadcasts and channels not covered by the
contract can be selected during manual tuning.
1.
Press the
[SEEK/MAN]
button.
*This changes the seek mode
to
manual mode
and
the "MANU" indicator
on
the display lights.
When this operation
is
performed
in
manual
mode, the seek mode
is
engaged
and
the
"MANU" indicator
on
the display goes
off.
Notes:
..
Operations cannot be performed for two seconds
afterpressing the [SEEK/MAN} button.
..
The
receiver automatically reverts
to
the seek
mode when the
["'j
or
["'''''J button is not used
for
7 seconds
in
the manual mode.
2.
Press the
[1-IIlII
....
] or [
..
~]
button. The receiver
moves to channels above or below the
current channel one by one.
3.
Press and hold the
[~
....
]
or
["'~J
for 1
second or longer.
The receiver moves
to
seek channels below
or above the current channel and the
channel found when either button is released
is received.
Recalling a
preset
channel
A total of 18 SIRIUS channels can be stored (6-
SRi,
6-SR2 and 6-SR3). This allows you
to
select your favorite SIRIUS channels and store
them
in
memory for later recall.
1.
Press the [SAT] button and select the desired
SIRIUS band (SR1, SR2 or SR3).
2.
To
recall a stored SIRIUS channel, press the
desired [DIRECT] button to select that
channel.
* Press and hold one
of
the [DIRECT] buttons
for 2 seconds or longer
to
store the current
channel into preset memory.
CMD4A 19
To Next Page
Loading...
