-3-
DXZ785USB/DXZ786USB
CAUTION
Use of controls, adjustments, or performance of procedures other
than those specified herein, may result in hazardous radiation ex-
posure.
The compact disc player should not be adjusted or repaired by
anyone except properly qualified service personnel.
Bottom view of DXZ785USB
11. Cautions in handling the optical pickup
The laser diode of the optical pickup can be damaged by elec-
trostatic charge caused by your clothes and body. Make sure
to avoid electrostatic charges on your clothes or body, or dis-
charge static electricity before handling the optical pickup.
11-1. Laser diode
The laser diode terminals are shorted for transportation in or-
der to prevent electrostatic damage. After replacement, open
the shorted circuit. When removing the pickup from the mecha-
nism, short the terminals by soldering them to prevent this
damage.
11-2. Actuator
The actuator has a powerful magnetic circuit. If a magnetic
material is put close to it. Its characteristics will change. En-
sure that no foreign substances enter through the ventilation
slots in the cover.
10. Cautions in checking that the optical pickup lights up.
The laser is focused on the disc reflection surface through the
lens of the optical pickup. When checking that the laser opti-
cal diode lights up, keep your eyes more than 30cms away
from the lens. Prolonged viewing of the laser within 30cms
may damage your eyesight.
11-3. Cleaning the lens
Dust on the optical lens affects performance.
To clean the lens, apply a small amount of isopropyl alcohol to
lens paper and wipe the lens gently.
ERROR DISPLAYS
If an error occurs, one of the following displays is displayed. Take the measures described below to eliminate the problem.
* If an error display other than the ones described above appears, press the reset button.
* When the power supply is turned on for the first time, the bolero microcomputer version display is mistake.
It is solved by turning ACC on and off once again.
Error Display Cause Measure
ERROR 2 A CD is caught inside the CD deck and is not ejected. This is a failure of CD deck’s mechanism.
ERROR 3 A CD cannot be played due to scratches, etc. Replace with a non-scratched, non-warped-disc.
ERROR 6 A CD is loaded upside-down inside the CD deck and Eject the disc then reload it properly.
does not play.
ERROR 2 A CD inside the CD changer is not loaded. This is a failure of CD changer’s mechanism.
ERROR 3 A CD inside the CD changer cannot be played due to Replace with a non-scratched, non-warped disc.
scratches, etc.
ERROR 6 A CD inside the CD changer cannot be played Eject the disc then reload it properly.
because it is loaded upside-down.
ERROR 2 A DISC inside the DVD changer cannot be played. This is a failure of DVD mechanism.
ERROR 3 A DISC cannot be played due to scratches, etc. Retry or replace with a non-scratched,
non-warped disc.
ERROR 6 A DISC inside the DVD changer cannot be played Eject the disc then reload it properly.
because it is loaded upsidedown.
ERROR P Parental level error Set the correct Parental level.
ERROR R Region code error Eject the disc and replace correct region code disc.
ERROR 2 The files are not proper MP3/WMA/AAC format. Use only properly encoded MP3/WMA/AAC files.
ERROR 3 The MP3/WMA/AAC files are improperly encoded. Use only properly encoded MP3/WMA/AAC files.
(USB/MTP mode)
ERROR 3 The iPod contains no audio files. Insert an iPod containing audio files.
(iPod mode)
ERROR 5 The connected devices are not recognized. Disconnect the devices and reconnect.
BUS-PWR Overcurrent detection. Disconnect the devices and reconnect. If the
devices are still not recognized, try replacing with
a different devices.
HUB The connected devices are not recognized. Disconnect the devices and reconnect. If the
devices are still not recognized, try replacing with
a different devices.
PE-3041B
276-0379-00
To Next Page
Loading...
Need help?
General
