Clarion DXZ838RMP - Page 9

DXZ838RMP 13
English
Basic Operations
Adjusting the tone
Press the [A-M] button and select the item to
adjust. Each time you press the [A-M] button,
the item changes in the following order:
● When the BEQ (BASS BOOST, IMPACT,
EXCITE) is set
“SW-VOL” ➜ “BASS BOOST” ( IMPACT,
EXCITE) ➜ “BALANCE” ➜ “FADER” ➜
Function mode...
● When the BEQ (USER CUSTOM) is set
“SW-VOL” ➜ “BASS” ➜ “MID” ➜
“TREBLE” ➜ “BALANCE” ➜ “FADER” ➜
Function mode…
● When the TONE BYPASS is set
“SW-VOL” ➜ “BALANCE” ➜ “FADER” ➜
Function mode…
∗ Pressing the [BEQ] button for 1 second or
longer while in “USER CUSTOM” sets flat, and
displays a “BEQ FLAT” message.
Note:
• When the separately-sold digital sound processor
(DVH923) is used, the bass and treble tone
adjustments cannot be selected.
Adjusting the subwoofer output
volume
You can adjust the volume output from the
unit’s subwoofer output terminal.
1. Press the [A-M] button and select “SW-
VOL”.
2. Turning the [ROTARY] knob clockwise
increases the output volume; turning it
counterclockwise decreases the output
volume.
∗ The factory default setting is “0”. (Setting range:
–6 to 6)
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the bass
The bass gain, bass F (center frequency) and
bass Q can be adjusted as follows.
1. Press the [A-M] button and select “BASS
Å
GAIN
Î
”.
2. Press the [a] or [d] button and select
from “BASS
Å
GAIN
Î
” ➜ “BASS
Å
F 50
Î
”
➜ “BASS
Å
Q 1
Î
” ➜ “BASS
Å
GAIN
Î
”.
3. Turn the [ROTARY] knob clockwise or
counterclockwise as needed and adjust the
gain, the F (center frequency) and the Q.
BASS GAIN : –6 to 8 (The factory default
setting is “0”)
BASS F : 50Hz/80Hz/120Hz (The
factory default setting is “50”)
BASS Q : 1/1.25/1.5/2 (The factory
default setting is “1”)
4. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the MID
The MID gain, MID F (center frequency) and
MID Q can be adjusted as follows.
1. Press the [A-M] button and select “MID
Å
GAIN
Î
”.
2. Press the [a] or [d] button and select
from “MID
Å
GAIN
Î
” ➜ “MID
Å
F 1k
Î
” ➜
“MID
Å
Q 2
Î
” ➜ “MID
Å
GAIN
Î
”.
3. Turn the [ROTARY] knob clockwise or
counterclockwise as needed and adjust the
gain, the F (center frequency) and the Q.
MID GAIN : –6 to 6 (The factory default
setting is “0”)
MID F : 700Hz/1KHz/2KHz (The factory
default setting is “1k”)
MID Q : 1.5/2 (The factory default
setting is “2”)
4. When the adfustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the TREBLE
The treble gain and treble F (center frequency)
can be adjusted as follows.
1. Press the [A-M] button and select “TREB
Å
GAIN
Î
”.
2. Press the [a] or [d] button and select
from “TREB
Å
GAIN
Î
” ➜ “TREB
Å
F 12K
Î
”
➜ “TREB
Å
GAIN
Î
”.
3. Turn the [ROTARY] knob clockwise or
counterclockwise as needed and adjust the
gain and the F (center frequency).
TREB GAIN : –6 to 6 (The factory default
setting is “0”)
TREB F : 8KHz/12KHz (The Factory
default setting is “12K”)