Clarion DXZ838RMP User Manual

14 DXZ838RMP
English
Adjusting MAGNA BASS EXTEND
The MAGNA BASS EXTEND does not adjust
the low sound area like the normal sound
adjustment function, but emphasizes the deep
bass sound area to provide you with a dynamic
sound.
∗ The factory default setting is off.
1. Press and hold the [A-M] button for 1 sec-
ond or longer to turn on the MAGNA BASS
EXTEND effect.
“M-B EX” lights in the display.
2. Press and hold the [A-M] button for 1 second
or longer to turn off the MAGNA BASS EX-
TEND effect.
“M-B EX” goes off from the display.
CT (Clock Time) function
The CT function receives CT data sent from an
RDS station and displays the time. Press the [D]
button to switch to the CT display.
∗ If a CT data is not being received, “CT––:––” ap-
pears in the display.
Note:
• CT data is not transmitted in some countries and
by some broadcast stations. Also, in some areas,
the CT may not display accurately.
Basic Operations
4. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the balance
1. Press the [A-M] button and select
“BALANCE”.
2. Turning the [ROTARY] knob clockwise
emphasizes the sound from the right
speaker; turning it counterclockwise
emphasizes the sound from the left
speaker.
∗ The factory default setting is “0”. (Adjustment
range: L13 to R13)
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the fader
1. Press the [A-M] button and select “FADER”.
2. Turning the [ROTARY] knob clockwise
emphasizes the sound from the front
speakers; turning it counterclockwise
emphasizes the sound from the rear
speakers.
∗ The factory default setting is “0”. (Adjustment
range: F12 to R12)
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the Beat EQ
1. Press the [BEQ] button and select the Beat
EQ mode (1 to 3) to adjust.
2. Press the [A-M] button and select “BASS
BOOST” or “IMPACT” or “EXCITE”.
3. Turning the [ROTARY] knob clockwise
adjusts in the + direction; turning it
counterclockwise adjusts in the – direction.
∗ When BASS BOOST is selected, you can
adjust the bass in the range of –3 to 3.
∗ When IMPACT and EXCITE is selected, you
can adjust the bass and treble in the range of –3
to 3.
4. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.

Clarion DXZ838RMP Specifications

Radio Section

FM receiving frequencies	87.5 to 108 MHz (0.05 MHz steps)
MW receiving frequencies	531 to 1602 kHz (9 kHz steps)
LW receiving frequencies	153 to 279 kHz (3 kHz steps)

CD Player Section

frequency response	5 Hz to 20 kHz (± 1 dB)
signal to noise ratio	100 dB (1 kHz) IHF-A
dynamic range	95 dB (1 kHz)

General Specifications

output power	4 ✕ 31 W (DIN 45324, +B=14.4V)
power supply voltage	14.4 V DC (10.8 to 15.6 V allowable)
power consumption	Less than 15 A

Weight and Dimensions

main unit weight	1.6 kg
remote control unit weight	30 g (including battery)
main unit dimensions	178 (W) ✕ 50 (H) ✕ 155 (D) mm