Clarion DXZ938R User Manual

DXZ938R 13
English
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Operation BASS/TREB
1. Press the “BASS/TREB” mode. Each time
the [EQ] button is pressed, the adjusting item
“BASS” or “TREB” is changed cyclically.
2. Turn the [ROTARY] knob clockwise or coun-
terclockwise to adjust “BAS/TREB”.
3. Press the [EQ] button to return to the previ-
ous mode.
∗ The Adjustment range is from -6dB to +6dB
for bass and treb.
∗ This parameter is reflected STD PRO mode
Speaker Setting
You can set up your favorite sound environment
using “Dolby Surround Pro logic II” or “AC-
Processor II” so that you can enjoy a dynamic
sound of 5.1 ch surround or 4ch + 2ch speaker.
●Dolby Pro Logic II 5.1ch surround
Center SP +Front L.R. +Surround L.R. +Sub
Woofer.
To make the most of the sound field reproduc-
tion of Dolby Pro Logic II , a speaker system of
5.1 channel is recommendable. It has been also
designed so that a sound filed effect almost as
good as that of 5.1 channel reproduction can be
obtained even by a constitution of 4 channel + 1
channel (subwoofer).
If you using Dolby Pro Logic source and your
speaker is only four Front L.R. + Surround L.R.,
speaker setting will be better to CTR+SW and
CTR OFF, so Center channel divided to Front
L.R. automatically.
Note
• When SW-L + SW-R are chosen, audio output
from SW-L is not available in the PL
II mode.
●AC- Processor II
Front L.R. + Rear L.R.+ Sub Woofer L.R. (4ch +
2ch)
To make the most of the sound field reproduc-
tion of AC-Processor II , a speaker system of 4
channel + 2 channel is recommendable.
1. Press and hold the [TITLE] button for 1 sec-
ond or longer and enter “ADJ” mode.
2. Press the [a] or [d] button to select the
“SP-SETTING”.
3. Turn the [ROTARY] knob clockwise or coun-
terclockwise to select “SW L+SW R” or “CTR
+SW” mode.
Basic Operations
Note:
• When CTR + SW are chosen, audio output from
CTR is not available except in the PL
II mode.
Center Speaker and Sub Woofer On / Off
Select PLII Mode on and SP setting to
“CTR+SW” mode
1. Press and hold the [TITLE] button for 1 sec-
ond or longer.
2. Press the [a] or [d] button to select the
“SP SEL”.
3. Press the [
] button to adjust the “CTR-
SP” “SUB W”.
4. Turn the [ROTARY] knob clockwise or coun-
terclockwise to select “ON” or “OFF”.
∗ This function is useful for Speaker Setting
Problems.
Filter Adjustment
1. Select Dolby Pro Logic II or AC-ProII mode
and press and hold the [TITLE] button for 1
second or longer.
2. Press the [a] or [d] button to select the
“FILTER”.
3. Press the [
] button to adjust the “SUB-W
LPF” or “HPF”.
4. Turn the [ROTARY] knob clockwise or coun-
terclockwise to adjust filter frequency.
∗ Sub Woofer Low Pass Filter Adjustment
Range is 50, 80, 120Hz (18dB/oct), OFF.
∗ When PLII mode Sub Woofer Low pass Filter
Adjustment Range is 50, 80, 120Hz (12dB/
oct.), OFF.
∗ High Pass Filter adjustment Range is 50, 80,
120Hz(12dB/oct), thrgh.
Note:
• High pass filter adjustment is available for Front
2ch and Rear 2ch only AC-Pro
II PRO Mode.
CT (Clock Time) function
The CT function receives CT data sent from an
RDS station and displays the time. Press the
[DISP] button to switch to the CT display.
∗ If a CT data is not being received, “CT––:––” ap-
pears in the display.
Note:
• CT data is not transmitted in some countries and
by some broadcast stations. Also, in some areas,
the CT may not display accurately.

Clarion DXZ938R Specifications

Radio Specifications

FM receiving frequency range	87.5 to 108 MHz (0.05 MHz steps)
MW receiving frequency range	531 to 1602 kHz (9 kHz steps)
LW receiving frequency range	153 to 279 kHz (3 kHz steps)

CD Player Specifications

frequency response	5 Hz to 20 kHz (± 1 dB)
signal to noise ratio	100 dB (1 kHz) IHF-A
dynamic range	96 dB (1 kHz)

General Specifications

output power	4 x 31 W (DIN 45324, +B=14.4V)
power supply voltage	14.4 V DC (10.8 to 15.6 V allowable)
power consumption	Less than 15 A

Weight and Dimensions

main unit weight	1.7 kg
remote control unit weight	30 g (including battery)
main unit dimensions	178 (W) x 50 (H) x 155 (D) mm