Clarion PJ-4604T - User Manual

Questions and Answers

T
tylerscottAug 16, 2025
Why can't I pair my Bluetooth device with Clarion Car Receiver?
- R
  rebecca20Aug 16, 2025
  If you cannot pair your Bluetooth device with the Clarion Car Receiver, it could be due to several reasons. First, the device may not support the profiles required for the system, in which case you should use another device to pair. Second, the Bluetooth function of the device may not be enabled; refer to the user manual of the device for instructions on how to enable it. Finally, the Bluetooth information may not match; delete the paired device on both your Bluetooth device and the car audio system, and then pair them again.
T
taylormaryAug 19, 2025
What to do if Clarion Car Receiver has no sound with amplifiers or power antenna?
- A
  Ashley ScottAug 19, 2025
  If you're not getting any sound from your Clarion Car Receiver when using amplifiers or a power antenna, the power antenna lead may be shorted to ground, or the amplifiers or power antenna may require excessive current. To resolve this: 1. Turn the unit off. 2. Remove all wires attached to the power antenna lead and check each wire for a short to ground using an ohm meter. 3. Turn the unit back on. 4. Reconnect each amplifier remote wire to the power antenna lead one by one. If the amplifiers turn off before all wires are attached, use an external relay to provide remote-on voltage.
S
strongloganAug 22, 2025
Why does the sound skip or is noisy on my Clarion Car Receiver?
- G
  Gregory McdanielAug 22, 2025
  If the sound from your Clarion Car Receiver skips or is noisy, the compact disc may be dirty. Clean it with a soft cloth. Alternatively, the compact disc might be heavily scratched or warped, in which case you should replace it with a compact disc that has no scratches.
R
reyesamandaAug 26, 2025
How to improve Bluetooth audio quality on Clarion Car Receiver?
- C
  Caleb DorseyAug 26, 2025
  If the Bluetooth hands-free audio quality isn't improved after connecting a Bluetooth device to your Clarion Car Receiver, the external microphone may not be set correctly or properly positioned. Adjust the gain and position of the external microphone. For example, stick the microphone onto the dashboard so it is close to the driver.
T
Thomas DanielsAug 28, 2025
What to do if buttons don't work on Clarion Car Receiver?
- J
  James ReidAug 28, 2025
  If nothing happens when you press the buttons on your Clarion Car Receiver and the display is not accurate, the DCP or main unit connectors might be dirty. Wipe the dirt off with a soft cloth moistened with cleaning alcohol.
T
tracysnyderAug 31, 2025
Why is the sound cut or skipped on my Clarion Car Receiver?
- B
  Brian BensonAug 31, 2025
  If the sound from your Clarion Car Receiver is cut or skipped, the MP3/WMA files might not be encoded properly. Use MP3/WMA files encoded properly.
P
Pamela ShieldsSep 3, 2025
Why does my Clarion Car Receiver show the wrong filename?
- M
  Mark MarshallSep 3, 2025
  If your Clarion Car Receiver displays the wrong filename, the file system might not be correct. Use ISO9660 level 1, 2 or JOLIET or Romeo or APPLE ISO file system.
D
Daniel BatesSep 6, 2025
Why is the sound bad when I turn on my Clarion Car Receiver?
- R
  rebeccahowellSep 6, 2025
  If the sound quality of your Clarion Car Receiver is poor immediately after turning it on, water droplets may have formed on the internal lens due to parking in a humid place. Let it dry for about 1 hour with the power on.
J
Justin MathisSep 9, 2025
What to do if Clarion Car Receiver doesn’t recognize the device?
- L
  Linda WyattSep 9, 2025
  If your Clarion Car Receiver doesn't recognize the device, the device may be damaged. Disconnect the device and reconnect. If it's still not recognized, try replacing it with a different device.
K
Keith FitzgeraldSep 12, 2025
Why can’t I insert the device into my Clarion Car Receiver?
- B
  Brian HughesSep 13, 2025
  If you can't insert the device into your Clarion Car Receiver, the device may have been inserted improperly. Try reversing the connection direction of the device (usually the brand name surface should be facing left). Alternatively, the connector may be broken, in which case you should replace it with a new device.