To Next PageTo Next Page
Need help?Do you have a question about the Clarion VRX613R and is the answer not in the manual?
General| Motorized | Yes |
|---|---|
| Touchscreen | Yes |
| Bluetooth | No |
| USB Port | No |
| DVD Player | Yes |
| CD Player | Yes |
| MP3 Playback | Yes |
| WMA Playback | Yes |
| AM/FM Radio | Yes |
| Remote Control | Yes |
| Preamp Outputs | 3 pairs (front, rear, subwoofer) |
| AAC Playback | No |
| Audio Output Power | 50 watts x 4 channels |
| Video Playback Formats | DVD, VCD |
| Aux Input | Yes |
| Video Output | 1 |
Technical details on frequency range, output power, speaker impedance, and audio input/output.
Details on screen size, display method, pixels, power source, and general operational parameters.
Guidance on cable length, PWB repair, CD compatibility, CD-text features, and design change notices.
List of components included with the main unit and the remote control, with part numbers.
Guidelines for engineers covering safe part usage, wiring, chip handling, and flexible PWB precautions.
Emphasis on safety checks, securing parts, correct wiring, and general disassembly procedures.
Explanation of error codes displayed by CD and MD changers related to disc loading and playback.
Troubleshooting steps for when the unit shows no response to buttons or has an inaccurate display.
Detailed explanation of each pin's function for the AV Center System Controller IC (M30624MG-D58GP).
Table detailing how AUX IN signals are selected based on specific input pin configurations.
Table explaining the selection of image sources based on the status of specific input pins.
Procedures for connecting equipment and initiating the system check sequence for the unit.
Instructions for adjusting the DC-DC converter output voltage and the frequency of IC706.
Steps for adjusting video signal parameters, brightness, and color (RGB-AMP/CONT-G) settings.
Procedures for adjusting H-sync pulse, VCOM DC bias, and burst cleaning for optimal display.
Exploded view diagram and list of parts for the DCP (Digital Control Panel) section of the unit.
Exploded view diagram and list of parts for the LCD module assembly.
Exploded view diagram and list of parts for the main unit assembly.
A comprehensive block diagram illustrating the interconnections between all major system modules.
List of accessory parts and hardware, such as screws, fuses, and cords, for the main section.
Step-by-step instructions for safely removing the LCD module from the main unit assembly.
Detailed list of parts for the DCP section, including part numbers and quantities.
Detailed list of parts for the LCD module, including part numbers and quantities.
Detailed list of parts for the main unit section, including part numbers and quantities.
Comprehensive list of electrical components (capacitors, diodes, ICs) used on the Main PWB (B1).
Exploded view diagram and list of parts for the slide mechanism assembly.
Important cautions and procedures for replacing the motor assembly, including current checks.
Comprehensive list of electrical components (capacitors, resistors, ICs) used on the Digital PWB (B2).
Partial list of electrical components for the Digital PWB (B3), continuing the component listing.
Continuation of the electrical component list for the Digital PWB (B3).
List of electrical components and their details for the DCP PWB (B4).
List of electrical components used on the LCD PWB (B3).
First half of the circuit diagram for the Main PWB (B1), showing component interconnections.
Second half of the circuit diagram for the Main PWB (B1), completing the module schematic.
Printed wiring board layout diagram for the Main PWB (B1), showing component placement.
First half of the circuit diagram for the Digital PWB (B2), illustrating its circuitry.
Second half of the circuit diagram for the Digital PWB (B2), showing the complete circuit.
Printed wiring board layouts for the Digital PWB (B2) and the DCP PWB (B4).
Circuit diagram detailing the components and connections on the DCP PWB (B4).
Printed wiring board layouts for the LCD PWB (B3) and the DCP PWB (B4).
Printed wiring board layouts for the LCD PWB (B3) and the DCP PWB (B4).
