Clarke Clean Track 18 Wash Rinse User Manual

Electronic Service
Manuals
This electronic document is provided as a service to our customers.
We do not create the contents of the information contained in this docu-
ment. Should you have detailed questions pertaining to the information
contained in this document, you may contact Michco, or the manufac-
turer which provided the original information in this electronic deliver-
able. Michco’s only part in this electronic deliverable was the electronic
assembly process. By providing this manual on line we are not guaran-
teeing parts availability.
You may contact Michco through the following methods:
Phone (517) 484-9312 or (800) 331-3339
2011 N. High St. -- Lansing, Michigan -- 48906
Fax: (517) 484-9836
Email: CustServe@Michco.com
Web site: www.Michco.Com
Parts Web site: www.FloorMachineParts.Com
Order Parts on Line at:
www.FloorMachineParts.Com
Directly to Parts & Service:
By Email: Shop@Michco.com
By Fax: (517) 702-2041
By Voice: Use numbers above.
Serving the Cleaning Industry Since 1922
Notice: All copyrighted material remains property of original owners, all trademarks are property of respective owners.
Manuals are subject to Manufacturer’s reproduction limitations. Originals or reproductions were provided by manufacturers
through a request. We make no warranty as to the correctness of information provided in this document and you assume
all risk. By placing these manuals on line we are not declaring our corporation to be an manufacturer authorized dealer or
provider, please check our web site for authorized manufacturers we represent.

Clarke Clean Track 18 Wash Rinse Specifications

General

Model	Clean Track 18 Wash Rinse
Category	Floor Machine
Brush Motor	0.75 hp
Cleaning Path	18 inches
Power Cable Length	50 feet
Power Source	Electric
Voltage	120 V
Amperage	14 A
Vacuum Motor	0.5 hp
Brush Width	18 inches
Machine Width	20 inches
Tank Capacity	3.5 gallons

Summary

INTRODUCTION

IMPORTANT SAFETY INSTRUCTIONS

120VAC GROUNDING INSTRUCTIONS

KNOW YOUR MACHINE

PREPARING THE MACHINE FOR USE

FILLING THE SOLUTION TANK

Instructions for filling the solution tank with water and cleaner.

BEFORE USING THE CLEAN TRACK®

Steps to take before operating the machine.

PRE-SPRAYING THE CARPET

Guidance on pre-spraying carpet before extraction.

PLAN FOR CLEANING

Strategy for planning cleaning routes and passes.

OPERATING THE MACHINE

USING ATTACHMENTS

How to connect and use optional accessory tools.

HARD FLOOR KITS

Information on using squeegee tools for hard floors.

AFTER USING THE MACHINE

MAINTENANCE SCHEDULE

Recommended daily, weekly, monthly, and yearly maintenance tasks.

VACUUM SHOE MAINTENANCE

Procedure for cleaning and maintaining the vacuum shoe.

MAINTENANCE PROCEDURES

SPRAY NOZZLE MAINTENANCE

How to clean and maintain the spray nozzles weekly.

SOLUTION SCREEN MAINTENANCE

How to clean the solution screen weekly.

POWER CORD MAINTENANCE

Weekly inspection of the power cord for damage.

ADJUSTING THE BRUSH PRESSURE

How to adjust brush pressure using the control knob.

POWER BRUSH MAINTENANCE

Daily checks for debris on the power brush.

REMOVING THE BRUSH

Step-by-step guide to removing and replacing the brush.

AUTHORIZED PERSONNEL MAINTENANCE

SOLUTION PUMP REMOVAL

Procedure for removing the solution pump.

SOLENOID VALVE REMOVAL (STANDARD MODELS)

Steps to remove the solenoid valve on standard models.

SOLENOID VALVE REMOVAL (WASH & RINSE MODEL)

Steps to remove the solenoid valve on Wash & Rinse models.

DEMA INJECTOR MAINTENANCE (WASH & RINSE MODEL)

How to maintain the DEMA injector on Wash & Rinse models.

BRUSH MOTOR REMOVAL

Procedure for removing the brush motor from the machine.

BRUSH DRIVE BELT REPLACEMENT

Steps to replace the brush drive belt.

VACUUM MOTOR MAINTENANCE

Maintenance for the vacuum motor, including carbon brushes.

TROUBLESHOOTING

TRIPPING THE CIRCUIT BREAKER

Causes and solutions for circuit breaker trips.

POOR WATER PICKUP

Diagnosing and fixing issues with water pickup.

INADEQUATE OR NO SOLUTION FLOW

Identifying causes for lack of solution flow.

INADEQUATE OR NO CHEMICAL INJECTION

Troubleshooting chemical injection problems.

TECHNICAL SPECIFICATIONS

Section II Parts Manual

Base Assembly

Exploded views and part numbers for the base of the machine.

Base Assembly (Nozzle Assemblies)

Specific parts for the nozzle assemblies of the base.

Brush Assembly

Components and part numbers for the brush system.

Decal System

Identification and placement of machine decals.

Handle System

Parts list for the machine's handle and control components.

Recovery Tank Assembly

Components and part numbers for the recovery tank.

Solution Tank Assembly

Components and part numbers for the solution tank.

Wiring Diagram-115V

Electrical schematic for 115V models.

Wiring Diagram-230V

Electrical schematic for 230V models.

Accessories

List of optional accessories available for the machine.

Clarke® U.S. WARRANTY

Clarke® Polydur Tank Guarantee

Details of the eight-year guarantee for Polydur tanks.