EasyManua.ls Logo

Clarke TIGER 1800 - User Manual

Clarke TIGER 1800
28 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
WARNING: Do not use the machine without reading this manual
OPERATION & MAINTENANCE
INSTRUCTIONS
LS1115
PETROL DRIVEN POWER WASHER
MODEL NO: TIGER 1800
PART NO: 7320200

Table of Contents

Questions and Answers

  • R
    Robert WalkerAug 13, 2025
    Why Clarke TIGER 1800 has no pressure on initial use?
    • K
      kelly86Aug 13, 2025
      If your Clarke Pressure Washer lacks pressure upon initial use, consider these potential causes: * **Leak in the high pressure hose fitting:** Tighten the fitting, using sealant tape if required. * **Nozzle obstruction:** Clear the nozzle. * **Clogged water filter screen:** Remove and clean the filter. * **Air in the hose:** Turn off the engine and water supply. Disconnect the water source and expel air from the hose. Reconnect, turn on the water, and pull the trigger to expel air from the gun/lance.
  • B
    brichardsonAug 17, 2025
    What to do if Clarke Pressure Washer will not draw chemicals?
    • E
      eporterAug 17, 2025
      If your Clarke Pressure Washer is not drawing chemicals, here are a few things to check: * **Blocked chemical filter:** Clean the filter. * **Chemicals too thick:** Dilute the chemicals to the consistency of water. * **High pressure hose too long:** Use a longer supply hose instead of a longer high pressure hose. * **Chemical build up:** Have the parts cleaned or replaced by your dealer.
  • L
    Laura JohnsonAug 21, 2025
    Why is my Clarke Pressure Washer leaking water from the drain hose?
    • L
      Laurie ParrishAug 21, 2025
      If your Clarke Pressure Washer is leaking water from the drain hose, this is normal. This is a safety feature to cool the pump by releasing some of the hot water and replacing it with fresh, cool water.
  • A
    Amanda KellyAug 25, 2025
    What causes lack of pressure in Clarke TIGER 1800 after normal use?
    • D
      Douglas MeltonAug 25, 2025
      If your Clarke Pressure Washer lacks pressure after a period of normal use: * **Worn seal or packing:** Have them replaced by your dealer. * **Worn or obstructed valves:** Have them replaced by your dealer.
  • M
    matthew48Aug 28, 2025
    How to fix Clarke TIGER 1800 Pressure Washer low pressure after starting?
    • S
      Stephanie GibsonAug 28, 2025
      If your Clarke Pressure Washer lacks pressure upon initial use, ensure that: * **Choke lever position:** Set the choke lever to the OFF position. * **Throttle control lever position:** Move the throttle control lever to the left. * **High pressure hose length:** Make sure the high pressure hose is under 100 feet.
  • L
    Lisa SmithSep 1, 2025
    Why is water leaking at the pump of my Clarke Pressure Washer?
    • J
      Jasmine BrownSep 1, 2025
      If you notice water leaking at the pump of your Clarke Pressure Washer: * **Loose connections:** Tighten them. * **Piston packings worn:** Have it replaced by your dealer. * **Worn or broken O-rings:** Have it replaced by your dealer. * **Pump head or tubes damaged from freezing:** Have it replaced by your dealer.
  • T
    Tiffany PerkinsSep 4, 2025
    What causes oil to leak at the pump of my Clarke Pressure Washer?
    • J
      James WallaceSep 4, 2025
      If oil is leaking at the pump of your Clarke Pressure Washer: * **Oil seals worn:** Have them replaced by your dealer. * **Worn O-rings:** Check and replace.
  • A
    Alexander HughesSep 8, 2025
    Why does the pump pulsate on my Clarke Pressure Washer?
    • M
      Michelle HendersonSep 8, 2025
      If the pump of your Clarke Pressure Washer pulsates, the nozzle may be obstructed. Clear the nozzle.

Summary

Safety Guidelines

General Safety Rules

Essential safety precautions to prevent injury and damage when operating the pressure washer.

Safety Symbols Explained

Explanation of various safety symbols and their meanings for safe operation.

Product Overview and Setup

Unpacking and Assembly

Instructions for unpacking and assembling the pressure washer, including fitting brackets.

Connecting Water Supply

Connecting Hoses and Lance

Procedure for connecting the high pressure hose, gun, and lance securely.

Preparation for Use

Before Use: Adding Engine Oil

Guidance on checking and filling the engine oil reservoir before operation.

Adding Fuel

Instructions for safely refuelling the petrol engine, including precautions.

Starting Your Pressure Washer

Step-by-step instructions for starting the pressure washer engine and initiating water flow.

Operation and Adjustment

Interrupting Operation

Adjusting the Spray Nozzle

Adjusting the Pressure

Applying Chemicals and Cleaning Agents

Shutting Down

Procedure for safely turning off and shutting down the pressure washer.

Maintenance

Cleaning the Nozzle

Cleaning the Water Inlet Filter

Cleaning the Fuel Strainer

Cleaning the Air Filter

Changing the Spark Plugs

Troubleshooting and Specifications

Troubleshooting Common Problems

Solutions for common issues such as engine not starting or lack of pressure.

Clarke TIGER 1800 Specifications

General IconGeneral
Motor Power1800W
Voltage230V
Hose Length5m
Maximum Pressure130 Bar
Flow Rate6.5 LPM
Max Pressure130 Bar
Water Flow6.5 LPM

Related product manuals