EasyManua.ls Logo

Clarke Tiger 2600B - User Manual

Clarke Tiger 2600B
28 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
WARNING: Do not use the machine without reading this manual
OPERATION & MAINTENANCE
INSTRUCTIONS
ORIGINAL INSTRUCTIONS GC0521
PETROL DRIVEN POWER WASHER
MODEL NO: TIGER 2600B
PART NO: 7320207

Table of Contents

Questions and Answers

  • B
    Brian PrestonAug 15, 2025
    How to fix a Clarke Tiger 2600B that won't start?
    • C
      Christopher NelsonAug 15, 2025
      If your Clarke Pressure Washer engine won't start, several issues could be the cause. First, ensure there is enough fuel and oil. Check that the spark plug lead is correctly attached and the engine switch is in the ON position. If the engine is warm, make sure the choke lever is in the OFF position (right). Also, verify that the fuel valve is open. If pressure has built up, squeeze the gun trigger to relieve it.
  • G
    gryanAug 18, 2025
    What to do if my Clarke Tiger 2600B Pressure Washer has lack of pressure on initial use?
    • B
      Bradley Carney Jr.Aug 18, 2025
      If your Clarke Pressure Washer lacks pressure upon initial use, check for the following: * Ensure there are no leaks in the high-pressure hose fitting; tighten it and use sealant tape if needed. * Clear any obstruction in the nozzle. * Clean the water filter screen. * Remove air from the hose by disconnecting the water source, turning it on to expel air, then reconnecting.
  • L
    lloydmatthewAug 21, 2025
    Why does my Clarke Tiger 2600B lack pressure even after initial use?
    • A
      Alexander FigueroaAug 21, 2025
      If your Clarke Pressure Washer continues to lack pressure after the initial use, ensure that the choke lever is in the OFF position and the throttle control lever is set high enough (moved to the left). Also, verify that the high-pressure hose is not longer than 100 feet.
  • S
    simmonschristinaAug 26, 2025
    What causes a Clarke Tiger 2600B to lose pressure after normal use?
    • T
      Tara MontoyaAug 26, 2025
      If your Clarke Pressure Washer loses pressure after a period of normal use, the issue may be worn seals or packing, or worn or obstructed valves. It is recommended to have these parts replaced by your dealer.
  • S
    Stefanie FrazierAug 28, 2025
    Why is my Clarke Pressure Washer leaking water at the pump?
    • B
      bbullockAug 28, 2025
      If your Clarke Pressure Washer is leaking water at the pump, check for loose connections and tighten them. Other potential causes include worn piston rings, damaged O-rings, or a pump head/tubes damaged from freezing. It is recommended to have these parts replaced by your dealer. See Storage.
  • T
    Timothy TylerAug 31, 2025
    Why Clarke Tiger 2600B will not draw chemicals?
    • A
      Adam PotterAug 31, 2025
      If your Clarke Pressure Washer will not draw chemicals, first check if the chemical filter is blocked and clean it. Ensure the chemicals being used are not too thick; they should have the consistency of water, so dilute if necessary. If the high-pressure hose is too long, use a longer supply hose instead. Chemical build-up inside the injector may also be the cause, so have the parts cleaned or replaced by your dealer.
  • T
    Tamara LeeSep 4, 2025
    How to stop a Clarke Tiger 2600B Pressure Washer pump from pulsating?
    • S
      Sarah LeeSep 4, 2025
      If your Clarke Pressure Washer pump is pulsating, the nozzle might be obstructed. Clear the nozzle to resolve this issue.
  • C
    Cassie PattersonSep 7, 2025
    What to do if Clarke Pressure Washer has oil leaking at the pump?
    • M
      melissahillSep 7, 2025
      If there's an oil leak at the pump of your Clarke Pressure Washer, it could be due to worn oil seals or O-rings. It is recommended to have them replaced by your dealer.
  • Z
    zaguilarSep 12, 2025
    Why is water leaking from the drain hose of my Clarke Pressure Washer?
    • J
      Jesse LongSep 12, 2025
      Water leaking from the drain hose of your Clarke Pressure Washer indicates that the pump is overheating. This is a safety feature to cool the pump by releasing some hot water and replacing it with fresh, cool water, so it should be expected.

Clarke Tiger 2600B Specifications

General IconGeneral
BrandClarke
ModelTiger 2600B
CategoryPressure Washer
LanguageEnglish

Related product manuals