EasyManua.ls Logo

Clarke TIGER 2600A - User Manual

Clarke TIGER 2600A
28 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
WARNING: Read these instructions before using the machine
OPERATION & MAINTENANCE
INSTRUCTIONS
LS0120 - ISS 1
ORIGINAL INSTRUCTIONS
PETROL DRIVEN POWER WASHER
MODEL NO: TIGER 2600A
PART NO: 7320206

Table of Contents

Questions and Answers

  • J
    John DaltonAug 14, 2025
    How to fix Clarke TIGER 2600A when engine will not start?
    • F
      fergusondanielAug 15, 2025
      If your Clarke Pressure Washer engine won't start, several factors could be at play. First, ensure you have enough fuel and oil. Check that the spark plug lead is securely attached and the engine switch is in the ON position. If the engine is warm, make sure the choke lever is in the OFF position. Also, verify that the fuel valve is open. If pressure builds up after a couple of pulls, squeeze the gun trigger to relieve the pressure.
  • J
    Jason MontesAug 18, 2025
    What to do if my Clarke TIGER 2600A Pressure Washer has lack of pressure on initial use?
    • R
      Richard ArnoldAug 18, 2025
      If your Clarke Pressure Washer lacks pressure upon initial use, start by checking for leaks in the high-pressure hose fitting and tighten if necessary, using sealant tape if needed. Clear any obstructions from the nozzle and clean the water filter screen. If there's air in the hose, turn off the engine and water supply. Disconnect the water source, expel the air, reconnect, and then pull the trigger to remove air from the gun/lance.
  • J
    john34Aug 21, 2025
    Why Clarke TIGER 2600A Pressure Washer has lack of pressure after a period of normal use?
    • D
      Dylan ParkerAug 21, 2025
      If your Clarke Pressure Washer loses pressure after normal use, the issue might be worn seals, packing, or obstructed valves. It is recommended to have these components replaced by your dealer.
  • U
    ucamachoAug 25, 2025
    What to do if my Clarke TIGER 2600A will not draw chemicals?
    • M
      Melissa LawsonAug 25, 2025
      If your Clarke Pressure Washer isn't drawing chemicals, first check if the chemical filter is blocked and clean it. Ensure the chemicals aren't too thick; they should have the consistency of water, so dilute them if needed. If you're using a long high-pressure hose, switch to a longer supply hose instead. For chemical build-up inside the injector, it is recommended to have the parts cleaned or replaced by your dealer.
  • J
    Joan TaylorAug 28, 2025
    Why my Clarke TIGER 2600A Pressure Washer pump pulsates?
    • J
      Janet GrossAug 28, 2025
      If your Clarke Pressure Washer pump pulsates, the nozzle may be obstructed. Clear the nozzle to resolve this issue.
  • H
    huffkaitlynAug 31, 2025
    What to do if my Clarke Pressure Washer is leaking water at the pump?
    • C
      Corey TurnerAug 31, 2025
      If your Clarke Pressure Washer is leaking water at the pump, start by tightening any loose connections. If the leak persists, the O-rings may be worn or broken, and it is recommended to have them replaced by your dealer. Damage from freezing may also cause leaks, in which case it is recommended to have the pump head or tubes replaced by your dealer.
  • O
    oscar36Sep 4, 2025
    What to do if my Clarke Pressure Washer has lack of pressure on initial use (continued)?
    • A
      Adam NunezSep 4, 2025
      If your Clarke Pressure Washer lacks pressure upon initial use, ensure the choke lever is in the OFF (right) position and the throttle control lever is moved to the left. Also, verify that the high-pressure hose is under 100 feet.
  • J
    josephmurraySep 7, 2025
    Why my Clarke Pressure Washer is leaking water from the drain hose?
    • N
      natashawillisSep 7, 2025
      Water leaking from the drain hose indicates that the pump is overheating. This is a normal safety feature that cools the pump by releasing some of the hot water and replacing it with fresh, cool water.
  • W
    William WilliamsSep 10, 2025
    What to do if my Clarke TIGER 2600A Pressure Washer has oil leaking at the pump?
    • M
      Matthew LambertSep 10, 2025
      If your Clarke Pressure Washer is leaking oil at the pump, it could be due to worn oil seals, in which case it is recommended to have them replaced by your dealer. Also, check the O-rings for wear and replace them if necessary.

Summary

PETROL DRIVEN POWER WASHER

OPERATION & MAINTENANCE INSTRUCTIONS

Provides guidance for operation and maintenance.

INTRODUCTION

GUARANTEE

ACCESSORIES

GENERAL SAFETY RULES

SAFETY SYMBOLS

OVERVIEW

ASSEMBLY

CONNECTING THE WHEELS

Steps to attach the wheels to the pressure washer frame.

FITTING THE HANDLE AND FEET

Guide for attaching the upper handle and rubber feet.

CONNECTING HOSES AND LANCE

Procedure for connecting the high-pressure hose and lance.

BEFORE USE

CONNECTING THE WATER SUPPLY

Instructions for connecting the water source to the machine.

ENGINE OIL AND FUEL

Guidance on checking oil level and refueling the engine.

STARTING YOUR PRESSURE WASHER

INTERRUPTING OPERATION

ADJUSTING THE SPRAY NOZZLE

ADJUSTING THE PRESSURE

APPLYING DETERGENTS AND CLEANING AGENTS

SHUTTING DOWN

WATER BUTT CONNECTION

STORAGE

BEFORE STORING THE PRESSURE WASHER

Steps to prepare the machine before storage.

STORAGE PROCEDURE

Recommended procedure for storing the unit.

MAINTENANCE

CLEANING THE NOZZLE

Instructions for cleaning the spray nozzle.

CLEANING THE WATER INLET FILTER

How to clean the water intake filter.

CLEANING THE FUEL STRAINER

Procedure for cleaning the fuel tank strainer.

CLEANING THE AIR FILTER

Steps to clean the engine's air filter.

CHANGING THE SPARK PLUGS

Guide for replacing the spark plug.

LONG TERM STORAGE

TROUBLESHOOTING

SPECIFICATIONS

EXPLODED DIAGRAM + PARTS LIST

DECLARATION OF CONFORMITY

Clarke TIGER 2600A Specifications

General IconGeneral
BrandClarke
ModelTIGER 2600A
CategoryPressure Washer
LanguageEnglish

Related product manuals