Clemco CLASSIC BLAST MACHINE - Replacement Parts Catalog; Machine, Hose, and Safety Accessories; Control System and Valve Parts

CLASSIC BLAST MACHINE with TLR-100/300 REMOTE CONTROLS Page 27
© 2018 CLEMCO INDUSTRIES CORP.  www.clemcoindustries.com  Manual No. 22501, Rev. I 02/18
7.9.2 Abrasive Does Not Stop When ACS Toggle is
Moved to OFF, Blowdown Mode.
7.9.2.1 Brass filter on ACS switch clogged. Inspect filter
for blockage.
7.9.2.2 Metering valve requires service. Refer to the
metering-valve manual for operation of the valve.
8.0 REPLACEMENT PARTS
8.1 Blast Machine Accessories
Description Stock No.
Cover, steel for
14" diameter machine ..................................... 02334
16" diameter machine ..................................... 02335
20" diameter machine ..................................... 20358
24" diameter machine ..................................... 02336
30" diameter machine ..................................... 02337
36" diameter machine .......................................... 28651
Cover, poly bag with Clemco logo for
2 and 3 cuft machines, medium ...................... 15097
4 and 6 cuft machines, large ........................... 15143
Screen, recessed type, for
14" diameter machine ..................................... 03098
16" diameter machine ..................................... 03099
20" diameter machine ..................................... 20357
24" diameter machine ..................................... 03100
30" diameter machine ..................................... 03101
36" diameter machine ..................................... 02391
Air filter, 1" NPT manual drain ............................... 22424
Air filter, 1" NPT auto drain .................................... 22425
Air filter, 1-1/2" NPT manual drain ......................... 22363
Air filter, 1-1/2" NPT auto drain .............................. 22364
8.2 Hose-Safety Accessories - Figure 27
NOTE: Spring-lock pins are affixed to nylon
couplings. When connecting two nylon coupling
together, make sure the coupling lock pins are at
180 degrees (Pins should enter the open hole of the
adjoining coupling.) One lock pin, as shown in Figure 27,
is used when connecting a nylon coupling to a metal
coupling, and two lock pins are used when connecting
two metal couplings together.
Item Description Stock No.
1. Safety cable
for 1-1/2" to 3" OD hose ........................ 15013
for 1-1/2" to 4" OD hose ........................ 27405
2. Lock pin, coupling (package of 25) ........... 11203
Figure 27
8.3 TLR-100/300 Remote Control Systems
Description Stock No.
TLR-100, 1" w/ piston outlet valve ......................... 01935
TLR-300, 1-1/4" w/ piston outlet valve ................... 01936
TLR-100D, 1" w/ diaphragm outlet valve ............... 03449
TLR-300D, 1-1/4" w/ diaphragm outlet valve ......... 03448
TLR-100C, 1" w/ACS and piston outlet valve ........ 21152
TLR-300C, 1-1/4" w/ACS and piston outlet valve . 21153
TLR-100DC, 1" w/ACS and dia. outlet valve ......... 21154
TLR-300DC, 1-1/4" w/ACS and dia. outlet valve ... 21155
8.4 Exhaust Muffler - Figure 28
Item Description Stock No.
(-) Muffler, complete ..................................... 05068
1. Screw, 8-32" x 4" ..................................... 05061
2. Cap, coated ............................................. 05067
3. Body, element .......................................... 05065
4. Screen ..................................................... 05060
5. Guide w/ guide nut .................................... 22344
6. O-ring, 1-1/4" ID ....................................... 05069
7. Seat ......................................................... 05062
8. Locknut, 8-32 ss ...................................... 05815
Figure 28
1
2
1
8
7
6
5
4
3
2