What causes high speaker failure rate in Code 3 Security System?
If you're experiencing a high rate of speaker failure with your Code 3 Security System, it could be caused by: * High voltage to the siren. Check the vehicle charging system. * Using an incorrect speaker. A 58-watt speaker connected to a 100-watt tap is not allowed; use the correct speaker.
Why does Code 3 Security System RRB shut off after extended use?
This is normal. The RRB shuts off after an extended period when the equipment starts to overheat. This is to avoid damage to the components in the amplifier. Allow the amplifier a few minutes to cool down.
Why does Code 3 Security System PA only function for 30 seconds?
This is normal behavior for the Code 3 Security System. The PA function turns off after 30 seconds to prevent a stuck microphone. To continue broadcasting, release the PTT button and press it again for another 30 seconds of broadcast ability.
What causes the LT light to be off when the 3 level switch is active on Code 3 Security System?
If the 3 level switch is active in any level but the LT light is off on your Code 3 Security System, it indicates that one or more of the 3 level fuses have blown in the amplifier. Replace the fuse(s) in the amplifier.
Why does my Code 3 Security System siren shut down and restart intermittently?
If your Code 3 Security System siren runs properly but shuts down intermittently, it may be due to vehicle circuit breakers that are not rated properly, are overheating, or are not functioning correctly. Refer to the specifications section on page 11 and use a breaker rated at 1.25 times the amperage of the expected load current.
Why is LT light off when auxiliary button is active on Code 3 Security System?
If the active auxiliary push button lights up but the LT light is off on your Code 3 Security System, one or more of the auxiliary fuses in the amplifier may have blown. Replace the fuse(s) in the amplifier.
Why are Code 3 Security System siren tones too low or garbled?
If the siren tones volume on your Code 3 Security System is too low or sounds garbled, it could be due to: * Low voltage to the siren amplifier. Check the wiring for bad connections and inspect the vehicle charging system. * High resistance in the wiring or a defective speaker. Check the speaker(s) wiring and consider replacing the speaker(s).
What to do if Code 3 Security System has no speaker output but tones are heard inside?
If you hear tones inside the amplifier module of your Code 3 Security System, but there's no output from the speaker and the SP indicator light is off, it could be due to: * The speaker not being connected or an open circuit in the speaker wiring. Check the speaker wiring. * Defective speakers. Replace the speaker(s).
How to troubleshoot low or no RRB volume on Code 3 Security System?
If the RRB (Radio Rebroadcast) volume is low or absent on your Code 3 Security System, the following could be the cause: * The radio rebroadcast volume may need to be increased. Refer to the setup and adjustment section. * The RRB wires might not be connected to the two-way radio's external speaker. Check the RRB connections.
What to do if Code 3 Automobile Accessories siren has no output?
If your Code 3 Automobile Accessories siren has no output, it could be due to several reasons. First, check if the park kill is activated and shift the vehicle out of park. Second, verify the SirenLock level and select the proper one. Lastly, inspect the speaker and speaker wires for shorts, as the siren might be in over-current protection mode. Check all connections to ensure they are properly secured.
Sirens produce loud sounds that may damage hearing; wear hearing protection.
Explains the function of the 3-level switch for changing warning modes.
Details on configuring auxiliary buttons, park kill, horn ring, and alerts.
Describes the Manual Wail tone and Hit-N-Go mode.
Details the Air Horn tone and its interaction with other features.
Explains the function and control of six auxiliary push-buttons.
Explains the Hit-N-Go feature activated by horn ring or manual button.
Describes how the horn ring scrolls through siren tones.
General| Brand | Code 3 |
|---|---|
| Model | XCEL Series |
| Category | Security System |
| Language | English |
To Next Page
