Code CR1100 User Manual

4
reset-clear-and-save-reader-settings...........................................................................................................................15
Reboot Reader (RCSRS) M2.................................................................................................................................................................15 (E2)
Reset to Factory Defaults M2..............................................................................................................................................................15 (E3)
Save All Reader Settings M2...............................................................................................................................................................15 (E4)
rs232-settings.................................................................................................................................................................16
Enable RS232 Interface Flow Control - One-Way M2.......................................................................................................................16 (A2)
Enable Serial, Raw, and Echo Communications M2.........................................................................................................................16 (A3)
Reset to RS232 Factory Defaults M2.................................................................................................................................................16 (A4)
RS232 Interface - 1 Stop Bit - Default M2.....................................................................................................................................16 (B2)
RS232 Interface - 115200 Baud Rate - Default M2.......................................................................................................................16 (B3)
RS232 Interface - 1200 Baud Rate M2............................................................................................................................................16 (B4)
RS232 Interface - 19200 Baud Rate M2..........................................................................................................................................16 (C2)
RS232 Interface - 2 Stop Bits M2.....................................................................................................................................................16 (C3)
RS232 Interface - 2400 Baud Rate M2............................................................................................................................................16 (C4)
RS232 Interface - 38400 Baud Rate M2..........................................................................................................................................16 (D2)
RS232 Interface - 4800 Baud Rate M2............................................................................................................................................16 (D3)
RS232 Interface - 57600 Baud Rate M2..........................................................................................................................................16 (D4)
RS232 Interface - 7 Data Bits M2....................................................................................................................................................16 (E2)
RS232 Interface - 8 Data Bits - Default M2...................................................................................................................................16 (E3)
RS232 Interface - 9600 Baud Rate M2............................................................................................................................................16 (E4)
RS232 Interface - Even Parity M2......................................................................................................................................................17 (A2)
RS232 Interface - No Parity M2.........................................................................................................................................................17 (A3)
RS232 Interface - Odd Parity M2.......................................................................................................................................................17 (A4)
RS232 Interface Flow Control Off - Default M2...............................................................................................................................17 (B2)
RS232 Interface Flow Control On M2.................................................................................................................................................17 (B3)
scan-delay-settings........................................................................................................................................................17
1 Day Duplicate Scan Delay M2.........................................................................................................................................................17 (C2)
1 Hour Duplicate Scan Delay M2.......................................................................................................................................................17 (C3)
1 Second Duplicate Scan Delay M2...................................................................................................................................................17 (C4)
10 Second Duplicate Scan Delay M2.................................................................................................................................................17 (D2)
2 Second Duplicate Scan Delay M2...................................................................................................................................................17 (D3)
3 Second Duplicate Scan Delay M2...................................................................................................................................................17 (D4)
30 Second Duplicate Scan Delay M2.................................................................................................................................................17 (E2)
5 Second Duplicate Scan Delay M2...................................................................................................................................................17 (E3)
Disable Duplicate Scan Delay - Default M2......................................................................................................................................17 (E4)
symbology-settings.........................................................................................................................................................18
Do Not Convert EAN-8 to EAN-13 - Default M2............................................................................................................................18 (A2)
Australian Post Off - Default M2.......................................................................................................................................................18 (A3)
Australian Post On M2.........................................................................................................................................................................18 (A4)
Aztec Inverse & Normal On M2..........................................................................................................................................................18 (B2)
Aztec Inverse Off - Default M2...........................................................................................................................................................18 (B3)
Aztec Mirror Off - Default M2.............................................................................................................................................................18 (B4)
Aztec Mirror On M2...............................................................................................................................................................................18 (C2)
Aztec Off M2..........................................................................................................................................................................................18 (C3)
Aztec On - Default M2.........................................................................................................................................................................18 (C4)
BC412 Off - Default M2......................................................................................................................................................................18 (D2)
BC412 On M2........................................................................................................................................................................................18 (D3)
Canada Post Off - Default M2...........................................................................................................................................................18 (D4)
Canada Post On M2.............................................................................................................................................................................18 (E2)
Codabar Checksum Off - Default M2.................................................................................................................................................18 (E3)
Codabar Checksum On M2...................................................................................................................................................................18 (E4)
Codabar Off M2.....................................................................................................................................................................................19 (A2)
Codabar On - Default M2....................................................................................................................................................................19 (A3)

Code CR1100 Specifications

General

Brand	Code
Model	CR1100
Category	Barcode Reader
Language	English