Code CR1100 User Manual

CR1100
B ARCODE R EAD I N G
Configuration barcodes generated based on current firmware versions
WEB GENERATED
4-17-2020

Code CR1100 Specifications

General

Humidity	5% to 95% (non-condensing)
Drop Specification	6 ft. / 1.8 m to concrete
Resolution	4 mil
Light Source	LED
Interfaces Supported	USB
Operating Temperature	0°C to 50°C
Storage Temperature	-20°C to 60°C
Supported Barcodes	UPC/EAN, Code 128, Code 39, Data Matrix, QR Code, Postal Codes
Interface	USB
Lighting	LED
Power Consumption	2.5 W

Summary

Communication Mode Settings

Enable IBM surePOS mode M2

Configure the reader to use IBM surePOS mode.

Enable Packet Mode M2

Configure the reader to use Packet Mode.

Enable Raw Mode - Default M2

Configure the reader to use Raw Mode.

Custom Terminal Settings

Disable Gilbarco - Default M2

Disable Gilbarco terminal emulation.

Disable NCR - Default M2

Disable NCR terminal emulation.

Disable NCR2 - Default M2

Disable NCR2 terminal emulation.

Disable WINCNIX - Default M2

Disable WINCNIX terminal emulation.

Enable Gilbarco M2

Enable Gilbarco terminal emulation.

Enable NCR M2

Enable NCR terminal emulation.

Enable NCR2 M2

Enable NCR2 terminal emulation.

Enable Verifone (Ruby) Defaults M2

Enable Verifone (Ruby) terminal defaults.

Enable WINCNIX M2

Enable WINCNIX terminal emulation.

Data Formatting Prefix Suffix Settings

Convert Barcode Data to Bracketed Hex Output M2

Format barcode data to bracketed hex output.

Convert Barcode Data to Lowercase M2

Format barcode data to lowercase.

Convert Barcode Data to Uppercase M2

Format barcode data to uppercase.

Disable Data Formatting - Default M2

Disable data formatting features.

Erase Prefix & Suffix Data M2

Erase prefix and suffix data.

Erase Prefix Data M2

Erase prefix data.

Erase Suffix Data M2

Erase suffix data.

Prefix AIM ID Off Default M2

Disable AIM ID prefix.

Prefix AIM ID On M2

Enable AIM ID prefix.

Prefix Comma M2

Add comma as prefix.

Prefix Space M2

Add space as prefix.

Prefix Tab (RS232 Mode Only) M2

Add tab as prefix for RS232.

Prefix Tab (USB Keyboard Mode Only) M2

Add tab as prefix for USB.

Suffix Carriage Return (RS232 Mode Only) M2

Add carriage return as suffix for RS232.

Suffix Carriage Return Line Feed (RS232 Mode Only) - Default M2

Add CR+LF as suffix for RS232.

Suffix Comma M2

Add comma as suffix.

Suffix Enter (USB Keyboard Mode Only) M2

Add enter key as suffix for USB.

Suffix Line Feed (RS232 Mode Only) M2

Add line feed as suffix for RS232.

Suffix Space M2

Add space as suffix.

Suffix Tab (RS232 Mode Only) M2

Add tab as suffix for RS232.

Suffix Tab (USB Keyboard Mode Only) M2

Add tab as suffix for USB.

Data Validation

Enable ISO15434 & ISO15418 Validation M2

Enable validation for ISO15434 and ISO15418.

Enable ISO15434 Validation M2

Enable validation for ISO15434.

Enable UDI/HIBC Validation M2

Enable validation for UDI/HIBC.

General Reading Mode Settings

500 ms Scan Delay with Motion Detection in stand - Default M2

Set 500ms scan delay with motion detection.

Beep Volume 0% M2

Set beep volume to 0%.

Beep Volume 100% - Default M2

Set beep volume to 100%.

Beep Volume 33% M2

Set beep volume to 33%.

Beep Volume 67% M2

Set beep volume to 67%.

Continuous Scan Mode On In Stand M2

Enable continuous scan mode in stand.

Continuous Scan Mode On M2

Enable continuous scan mode.

Disable Cell Phone Reading Enhancement - Default M2

Disable cell phone reading enhancement.

Enable Cell Phone Reading Enhancement M2

Enable cell phone reading enhancement.

Enable Stand Detection Default M2

Enable stand detection.

Enable Target LED During Image Capture Default M2

Enable target LED during image capture.

Enable Targeting-Always-On M2

Enable targeting always on.

Motion Detect Always On M2

Enable motion detection always on.

Motion Detect or Continuous Scan Off (Out of Stand) - Default M2

Disable motion detect in standby.

Motion Detection On In Stand - Default M2

Enable motion detection in standby.

Reader Raw Text Commands Off Default M2

Disable raw text commands.

Reader Raw Text Commands On M2

Enable raw text commands.

Set Motion Detect Maximum Brightness to 100% Default M2

Set motion detect max brightness to 100%.

Set Motion Detect Maximum Brightness to 25% M2

Set motion detect max brightness to 25%.

Set Motion Detect Maximum Brightness to 50% M2

Set motion detect max brightness to 50%.

Set Motion Detect Maximum Brightness to 75% M2

Set motion detect max brightness to 75%.

Trigger Mode On In Stand M2

Enable trigger mode in standby.

Keyboard Language Settings

Control Character Input - Alt + Keypad M2

Set control character input for Alt+Keypad.

Control Character Input - Ctrl + Character M2

Set control character input for Ctrl+Character.

Control Character Input - Language Default Default M2

Set default control character input language.

Control Character Input - Alt + Leading Zero M2

Set control character input for Alt+Leading Zero.

Data Encoding: Raw ASCII to Keyboard XML File Lookup - Default M2

Set data encoding to Raw ASCII for XML lookup.

Data Encoding: UTF8 to Unicode Codepoint Alt Sequences for Windows M2

Set data encoding to UTF8 for Unicode.

Get Active Language M2

Retrieve the active language setting.

Keyboard Support: English Keyboard Mapping for Apple M2

Set English keyboard mapping for Apple.

Keyboard Support: French Keyboard Mapping for Apple M2

Set French keyboard mapping for Apple.

Keyboard Support: French Keyboard Mapping for Windows M2

Set French keyboard mapping for Windows.

Keyboard Support: French-Belgian Keyboard Mapping for Windows M2

Set French-Belgian keyboard mapping for Windows.

Keyboard Support: German Keyboard Mapping for Apple M2

Set German keyboard mapping for Apple.

Keyboard Support: German Keyboard Mapping for Windows M2

Set German keyboard mapping for Windows.

Keyboard Support: German-Swiss Keyboard Mapping for Apple M2

Set German-Swiss keyboard mapping for Apple.

Keyboard Support: German-Swiss Keyboard Mapping for Windows M2

Set German-Swiss keyboard mapping for Windows.

Keyboard Support: Italian Keyboard Mapping for Apple M2

Set Italian keyboard mapping for Apple.

Keyboard Support: Japanese Keyboard Mapping for Windows M2

Set Japanese keyboard mapping for Windows.

Keyboard Support: Russian Keyboard Mapping for Windows M2

Set Russian keyboard mapping for Windows.

Keyboard Support: Simplified Chinese Keyboard Mapping for Windows M2

Set Simplified Chinese keyboard mapping for Windows.

Keyboard Support: Spanish Keyboard Mapping for Apple M2

Set Spanish keyboard mapping for Apple.

Keyboard Support: Spanish Keyboard Mapping for Windows M2

Set Spanish keyboard mapping for Windows.

Keyboard Support: Spanish-Latin American Keyboard Mapping for Windows M2

Set Spanish-Latin American keyboard mapping for Windows.

Keyboard Support: UK English Keyboard Mapping for Windows M2

Set UK English keyboard mapping for Windows.

Keyboard Support: US English Keyboard Mapping for Windows - Default M2

Set US English keyboard mapping for Windows.

Keyboard Support: US International (Universal) Keyboard Mapping for Windows M2

Set US International keyboard mapping for Windows.

List Installed Languages M2

List available keyboard languages.

Set Italian for Windows as active language M2

Set Italian as the active language for Windows.

Set Portuguese for Windows as active language M2

Set Portuguese as the active language for Windows.

Miscellaneous Settings

Disable Upload Image Mode - Default M2

Disable upload image mode.

Enable Upload Image Mode M2

Enable upload image mode.

Operating System Settings

Alternate Operating System (Linux/Mac) Off - Default M2

Disable alternate operating system (Linux/Mac).

Alternate Operating System (Linux/Mac) On M2

Enable alternate operating system (Linux/Mac).

Reader Modem Command Settings

Get Reader Parameters M2

Retrieve reader parameters.

Output Reader Configuration M2

Output the reader's configuration.

Reader Information, limited M2

Get limited reader information.

Reset Clear and Save Reader Settings

Reboot Reader (RCSRS) M2

Reboot the reader.

Reset to Factory Defaults M2

Reset reader settings to factory defaults.

Save All Reader Settings M2

Save all current reader settings.

RS232 Settings

Enable RS232 Interface Flow Control - One-Way M2

Enable one-way RS232 flow control.

Enable Serial, Raw, and Echo Communications M2

Enable serial, raw, and echo communications.

Reset to RS232 Factory Defaults M2

Reset RS232 settings to factory defaults.

RS232 Interface 1 Stop Bit - Default M2

Set RS232 interface to 1 stop bit.

RS232 Interface - 115200 Baud Rate - Default M2

Set RS232 baud rate to 115200.

RS232 Interface 1200 Baud Rate M2

Set RS232 baud rate to 1200.

RS232 Interface 19200 Baud Rate M2

Set RS232 baud rate to 19200.

RS232 Interface 2 Stop Bits M2

Set RS232 interface to 2 stop bits.

RS232 Interface 2400 Baud Rate M2

Set RS232 baud rate to 2400.

RS232 Interface 38400 Baud Rate M2

Set RS232 baud rate to 38400.

RS232 Interface 4800 Baud Rate M2

Set RS232 baud rate to 4800.

RS232 Interface 57600 Baud Rate M2

Set RS232 baud rate to 57600.

RS232 Interface 7 Data Bits M2

Set RS232 interface to 7 data bits.

RS232 Interface 8 Data Bits - Default M2

Set RS232 interface to 8 data bits.

RS232 Interface 9600 Baud Rate M2

Set RS232 baud rate to 9600.

RS232 Interface - Even Parity M2

Set RS232 interface to even parity.

RS232 Interface - No Parity M2

Set RS232 interface to no parity.

RS232 Interface - Odd Parity M2

Set RS232 interface to odd parity.

RS232 Interface Flow Control Off - Default M2

Disable RS232 interface flow control.

RS232 Interface Flow Control On M2

Enable RS232 interface flow control.

Scan Delay Settings

1 Day Duplicate Scan Delay M2

Set 1-day duplicate scan delay.

1 Hour Duplicate Scan Delay M2

Set 1-hour duplicate scan delay.

1 Second Duplicate Scan Delay M2

Set 1-second duplicate scan delay.

10 Second Duplicate Scan Delay M2

Set 10-second duplicate scan delay.

2 Second Duplicate Scan Delay M2

Set 2-second duplicate scan delay.

3 Second Duplicate Scan Delay M2

Set 3-second duplicate scan delay.

30 Second Duplicate Scan Delay M2

Set 30-second duplicate scan delay.

5 Second Duplicate Scan Delay M2

Set 5-second duplicate scan delay.

Disable Duplicate Scan Delay - Default M2

Disable duplicate scan delay.

Symbology Settings

Do Not Convert EAN-8 to EAN-13 Default M2

Prevent EAN-8 to EAN-13 conversion.

Australian Post Off Default M2

Disable Australian Post symbology.

Australian Post On M2

Enable Australian Post symbology.

Aztec Inverse & Normal On M2

Enable Aztec inverse and normal symbology.

Aztec Inverse Off Default M2

Disable Aztec inverse symbology.

Aztec Mirror Off Default M2

Disable Aztec mirror symbology.

Aztec Mirror On M2

Enable Aztec mirror symbology.

Aztec Off M2

Disable Aztec symbology.

Aztec On Default M2

Enable Aztec symbology.

BC412 Off Default M2

Disable BC412 symbology.

BC412 On M2

Enable BC412 symbology.

Canada Post Off Default M2

Disable Canada Post symbology.

Canada Post On M2

Enable Canada Post symbology.

Codabar Checksum Off Default M2

Disable Codabar checksum.

Codabar Checksum On M2

Enable Codabar checksum.

Codabar Off M2

Disable Codabar symbology.

Codabar On - Default M2

Enable Codabar symbology.

Codablock F Off Default M2

Disable Codablock F symbology.

Codablock F On M2

Enable Codablock F symbology.

Code 11 Checksum Stripped from Result Off Default M2

Disable Code 11 stripped checksum.

Code 11 Checksum Stripped from Result On M2

Enable Code 11 stripped checksum.

Code 11 Disable Checksum Checking - Default M2

Disable Code 11 checksum checking.

Code 11 Off Default M2

Disable Code 11 symbology.

Code 11 On M2

Enable Code 11 symbology.

Code 11 One Digit Checksum M2

Enable Code 11 one-digit checksum.

Code 11 Two Digit Checksum - Default M2

Enable Code 11 two-digit checksum.

Code 128 Off M2

Disable Code 128 symbology.

Code 128 On Default M2

Enable Code 128 symbology.

Code 32 (Italian Pharmacode) Off Default M2

Disable Code 32 (Italian Pharmacode) symbology.

Code 32 (Italian Pharmacode) On M2

Enable Code 32 (Italian Pharmacode) symbology.

Code 39 Checksum Off Default M2

Disable Code 39 checksum.

Code 39 Checksum On M2

Enable Code 39 checksum.

Code 39 Checksum Stripped from Result On M2

Enable Code 39 stripped checksum.

Code 39 Extended Full ASCII Off Default M2

Disable Code 39 Extended Full ASCII.

Code 39 Extended Full ASCII On M2

Enable Code 39 Extended Full ASCII.

Code 39 Off M2

Disable Code 39 symbology.

Code 39 On Default M2

Enable Code 39 symbology.

Code 49 Off - Default M2

Disable Code 49 symbology.

Code 49 On M2

Enable Code 49 symbology.

Code 93 Off M2

Disable Code 93 symbology.

Code 93 On - Default

Enable Code 93 symbology.

Composite On M2

Enable Composite symbology.

Composite Off - Default M2

Disable Composite symbology.

Convert Bookland EAN-13 to ISBN M2

Convert Bookland EAN-13 to ISBN.

Convert Bookland EAN-13 to ISSN M2

Convert Bookland EAN-13 to ISSN.

Convert EAN-8 to EAN-13 M2

Convert EAN-8 to EAN-13.

Convert UPC-A to EAN-13 M2

Convert UPC-A to EAN-13.

Custom QR Code Off Default M2

Disable Custom QR Code.

Custom QR Code On M2

Enable Custom QR Code.

Data Matrix Inverse and Normal On Default M2

Enable Data Matrix inverse and normal.

Data Matrix Inverse Off M2

Disable Data Matrix inverse.

Data Matrix Mirror Off Default M2

Disable Data Matrix mirror.

Data Matrix Mirror On M2

Enable Data Matrix mirror.

Data Matrix Off M2

Disable Data Matrix symbology.

Data Matrix On Default M2

Enable Data Matrix symbology.

Data Matrix Rectangular Extended Off Default M2

Disable Data Matrix rectangular extended.

Data Matrix Rectangular Extended On M2

Enable Data Matrix rectangular extended.

Data Matrix Rectangular Off M2

Disable Data Matrix rectangular.

Data Matrix Rectangular On Default M2

Enable Data Matrix rectangular.

Disable BC412 Regular and Reverse - Default M2

Disable BC412 regular and reverse.

Disable GS1 DataBar Expanded M2

Disable GS1 DataBar Expanded.

Disable GS1 DataBar Expanded Stacked M2

Disable GS1 DataBar Expanded Stacked.

Disable GS1 DataBar Limited M2

Disable GS1 DataBar Limited.

Disable GS1 DataBar Stacked and GS1 DataBar Stacked Omnidirectional M2

Disable GS1 DataBar Stacked and Omnidirectional.

Do Not Convert Bookland EAN-13 to ISBN - Default M2

Prevent Bookland EAN-13 to ISBN conversion.

Do Not Convert Bookland EAN-13 to ISSN - Default M2

Prevent Bookland EAN-13 to ISSN conversion.

Do Not Convert UPC-A to EAN-13 - Default M2

Prevent UPC-A to EAN-13 conversion.

Do Not Transmit EAN-13 Check Digit - Default M2

Disable EAN-13 check digit transmission.

Do Not Transmit EAN-8 Check Digit - Default M2

Disable EAN-8 check digit transmission.

Do Not Transmit UPC-A Check Digit - Default M2

Disable UPC-A check digit transmission.

Do Not Transmit UPC-A Number System - Default M2

Disable UPC-A number system transmission.

Do Not Transmit UPC-E Check Digit - Default M2

Disable UPC-E check digit transmission.

Do Not Transmit UPC-E Number System - Default M2

Disable UPC-E number system transmission.

Enable BC412 - Disable BC412 Reverse M2

Enable BC412 and disable reverse.

Enable GoCode & GoCode Mirror Decoding M2

Enable GoCode and GoCode Mirror decoding.

Enable GS1 DataBar Expanded - Default M2

Enable GS1 DataBar Expanded.

Enable GS1 DataBar Expanded Stacked - Default M2

Enable GS1 DataBar Expanded Stacked.

Enable GS1 DataBar Limited - Default M2

Enable GS1 DataBar Limited.

Enable GS1 DataBar Stacked and GS1 DataBar Stacked Omnidirectional - Default M2

Enable GS1 DataBar Stacked and Omnidirectional.

Grid Matrix Inverse Off Default M2

Disable Grid Matrix inverse.

Grid Matrix Inverse On M2

Enable Grid Matrix inverse.

Grid Matrix Mirror Off Default M2

Disable Grid Matrix mirror.

Grid Matrix Mirror On M2

Enable Grid Matrix mirror.

Grid Matrix Off Default M2

Disable Grid Matrix symbology.

Grid Matrix On M2

Enable Grid Matrix symbology.

GS1 DataBar Off M2

Disable GS1 DataBar symbology.

GS1 DataBar On Default M2

Enable GS1 DataBar symbology.

Han Xin Inverse Off Default M2

Disable Han Xin inverse.

Han Xin Inverse On M2

Enable Han Xin inverse.

Han Xin Mirror On M2

Enable Han Xin mirror.

Han Xin Normal and Inverse On M2

Enable Han Xin normal and inverse.

Han Xin Off - Default M2

Disable Han Xin symbology.

Han Xin On M2

Enable Han Xin symbology.

Hong Kong 2 of 5 Off Default M2

Disable Hong Kong 2 of 5 symbology.

Hong Kong 2 of 5 On M2

Enable Hong Kong 2 of 5 symbology.

Interleaved 2 of 5 Checksum Off - Default M2

Disable Interleaved 2 of 5 checksum.

Interleaved 2 of 5 Checksum On M2

Enable Interleaved 2 of 5 checksum.

Interleaved 2 of 5 Checksum Stripped from Result Off - Default M2

Disable Interleaved 2 of 5 stripped checksum.

Interleaved 2 of 5 Checksum Stripped from Result On M2

Enable Interleaved 2 of 5 stripped checksum.

Interleaved 2 of 5 Off M2

Disable Interleaved 2 of 5 symbology.

Interleaved 2 of 5 On Default M2

Enable Interleaved 2 of 5 symbology.

Japan Post Off - Default M2

Disable Japan Post symbology.

Japan Post On M2

Enable Japan Post symbology.

Keep Codabar Start and Stop Delimiters - Default M2

Keep Codabar start and stop delimiters.

Keep Trioptic Start and Stop Delimiters M2

Keep Trioptic start and stop delimiters.

KIX (Dutch Post) Off Default M2

Disable KIX (Dutch Post) symbology.

KIX (Dutch Post) On M2

Enable KIX (Dutch Post) symbology.

Korean Post Off Default M2

Disable Korean Post symbology.

Korean Post On M2

Enable Korean Post symbology.

Matrix 2 of 5 Off Default M2

Disable Matrix 2 of 5 symbology.

Matrix 2 of 5 On M2

Enable Matrix 2 of 5 symbology.

Maxicode Off - Default M2

Disable Maxicode symbology.

Maxicode On M2

Enable Maxicode symbology.

Micro PDF417 Off Default M2

Disable Micro PDF417 symbology.

Micro PDF417 On M2

Enable Micro PDF417 symbology.

Micro QR Code Off Default M2

Disable Micro QR Code symbology.

Micro QR Code On M2

Enable Micro QR Code symbology.

Mode 1 QR Code Off Default M2

Disable Mode 1 QR Code symbology.

Mode 1 QR Code On M2

Enable Mode 1 QR Code symbology.

MSI Plessey Checksum Must Be Mod 10 M2

Set MSI Plessey checksum to Mod 10.

MSI Plessey Checksum Must Be Mod 10/10 M2

Set MSI Plessey checksum to Mod 10/10.

MSI Plessey Checksum Must Be Mod 11/10 M2

Set MSI Plessey checksum to Mod 11/10.

MSI Plessey Checksum Off - Default M2

Disable MSI Plessey checksum.

MSI Plessey Checksum Stripped from Result Off - Default M2

Disable MSI Plessey stripped checksum.

MSI Plessey Checksum Stripped from Result On M2

Enable MSI Plessey stripped checksum.

MSI Plessey Off - Default M2

Disable MSI Plessey symbology.

MSI Plessey On M2

Enable MSI Plessey symbology.

NEC 2 of 5 Checksum Off M2

Disable NEC 2 of 5 checksum.

NEC 2 of 5 Checksum On - Default M2

Enable NEC 2 of 5 checksum.

NEC 2 of 5 Off Default M2

Disable NEC 2 of 5 symbology.

NEC 2 of 5 On M2

Enable NEC 2 of 5 symbology.

Output Telepen as ASCII M2

Output Telepen data as ASCII.

Output Telepen as Numeric - Default M2

Output Telepen data as numeric.

PDF417 Off M2

Disable PDF417 symbology.

PDF417 On - Default M2

Enable PDF417 symbology.

Pharmacode Color Off Default M2

Disable Pharmacode color.

Pharmacode Color On M2

Enable Pharmacode color.

Pharmacode Normal Barcode Decoding (Left to Right) - Default M2

Enable Pharmacode normal decoding.

Pharmacode Off Default M2

Disable Pharmacode symbology.

Pharmacode On M2

Enable Pharmacode symbology.

Pharmacode Reverse Barcode Decoding (Right to Left) M2

Enable Pharmacode reverse decoding.

QR Code Inverse and Normal On M2

Enable QR Code inverse and normal.

QR Code Inverse Only M2

Enable QR Code inverse only.

QR Code Mirror Off Default M2

Disable QR Code mirror.

QR Code Mirror On M2

Enable QR Code mirror.

QR Code Off M2

Disable QR Code symbology.

QR Code On - Default M2

Enable QR Code symbology.

QR Code Standard Only - Default M2

Enable QR Code standard only.

Remove Codabar Start and Stop Delimiters M2

Remove Codabar start/stop delimiters.

Remove Trioptic Start and Stop Delimiters - Default M2

Remove Trioptic start/stop delimiters.

Reverse BC412 Off Default M2

Disable Reverse BC412.

Reverse BC412 On M2

Enable Reverse BC412.

Reverse Trioptic Off - Default M2

Disable Reverse Trioptic.

Reverse Trioptic On M2

Enable Reverse Trioptic.

Royal Mail Checksum Off M2

Disable Royal Mail checksum.

Royal Mail Checksum On M2

Enable Royal Mail checksum.

Straight 2 of 5 Off Default M2

Disable Straight 2 of 5 symbology.

Straight 2 of 5 On M2

Enable Straight 2 of 5 symbology.

Telepen Off Default M2

Disable Telepen symbology.

Telepen On M2

Enable Telepen symbology.

Transmit EAN-13 Check Digit M2

Transmit EAN-13 check digit.

Transmit EAN-8 Check Digit M2

Transmit EAN-8 check digit.

Transmit UPC-A Check Digit M2

Transmit UPC-A check digit.

Transmit UPC-A Number System M2

Transmit UPC-A number system.

Transmit UPC-E Check Digit M2

Transmit UPC-E check digit.

Transmit UPC-E Number System On M2

Transmit UPC-E number system.

Trioptic Off Default M2

Disable Trioptic symbology.

Trioptic On M2

Enable Trioptic symbology.

UK Plessey Off - Default M2

Disable UK Plessey symbology.

UK Plessey On M2

Enable UK Plessey symbology.

UK Royal Mail Off Default M2

Disable UK Royal Mail symbology.

UK Royal Mail On M2

Enable UK Royal Mail symbology.

UPC E Expansion Off - Default M2

Disable UPC E Expansion.

UPC E Expansion On M2

Enable UPC E Expansion.

UPC Supplemental Off - Default M2

Disable UPC Supplemental.

UPC Supplemental On M2

Enable UPC Supplemental.

UPC/EAN Off M2

Disable UPC/EAN symbology.

UPC/EAN On - Default M2

Enable UPC/EAN symbology.

UPU ID Tags Off - Default M2

Disable UPU ID Tags.

UPU ID Tags On M2

Enable UPU ID Tags.

USPS Intelligent Mail Off - Default M2

Disable USPS Intelligent Mail.

USPS Intelligent Mail On M2

Enable USPS Intelligent Mail.

USPS Planet Off - Default M2

Disable USPS Planet.

USPS Planet On M2

Enable USPS Planet.

USPS Postnet Off - Default M2

Disable USPS Postnet.

USPS Postnet On M2

Enable USPS Postnet.

USB Settings

Enable CDC VCOM Mode M2

Enable CDC VCOM USB mode.

Enable HID POS Mode M2

Enable HID POS USB mode.

Enable USB VCOM mode M2

Enable USB VCOM mode.

Set reader into USB Full Speed mode - Default M2

Set USB reader to Full Speed mode.

Set reader into USB High Speed mode - Default M2

Set USB reader to High Speed mode.

USB HID Vendor Mode M2

Enable USB HID Vendor Mode.

USB Keyboard Mode - Default M2

Set USB reader to Keyboard Mode.

USB Virtual COM Common Ports M2

Enable USB Virtual COM Common Ports.

USB Virtual COM Multiple Ports M2

Enable USB Virtual COM Multiple Ports.