Coleman Ridgeview 9271L133 User Manual

Layout & Positioning
of Tent, Pole Assembly
– Layout and position tent with doors
facing desired direction. (illus. 1)
– Stake down tent corners,
using the tent stake loops.
Keep the floor taut. (illus. 2)
– Assemble all poles by interlocking
shock-corded poles.
– Insert the longer Center Frame Poles into
Center Pole Sleeves. The poles should cross
forming an “X” in the middle of tent. (illus. 1)
– Insert the shorter Side Frame Poles through the pole
sleeves located at the sides of tent. (illus. 1)
Connect Frame to Tent
– Unzip doors.
– Locate the Pin & Ring Systems on
either side of the front doors and the
corresponding Pin & Ring on the
back side of tent.
– Insert one end of Frame Pole onto
Pin & Ring System on tent stake loop
on either side of the doors. (illus. 3)
– Go to opposite end of pole diagonally
from starting point and gradually
apply pressure to the pole forming
an arch until you are able to insert
the Pin into pole end.
– Repeat for second pole.
– Attach tent frame clips to poles.
13’x13’ Ridgeview
1
2
When You Are Ready
To Set Up Your Tent
– Select a level campsite clear of
rocks, branches and other hard or
sharp objects.
– Do not set up your tent under trees.
– For best results in windy conditions,
position the end of tent into the wind.
(2) Side Tent
Poles
(2) Rainfly Poles
Rainfly Part No. 9271L104
(2) Center Tent
Poles
Door
Door
Instructions apply to Part Number 9271L133
illus. 1
illus. 2 Tent
stake through
stake loop
illus. 4
Center section upright
Part No. 9270L102
Part No. 9271L105
Part No. 9270L103
illus. 3
Ring & Pin System
Center poles
Side pole
Side pole
Center poles
Sidepole
Sidepole
POLE ASSEMBLY PARTS

Coleman Ridgeview 9271L133 Specifications

General

Brand	Coleman
Model	Ridgeview 9271L133
Category	Tent
Language	English

Summary

Pole Assembly Parts

Center Tent Poles

Identifies the two center poles used in the tent frame assembly.

Side Tent Poles

Identifies the two side poles for the tent frame structure.

Rainfly Poles

Identifies the poles specifically designed for the tent's rainfly.

Layout and Positioning of Tent

Prepare Campsite and Layout

Select a level site clear of obstructions and position the tent.

Stake Tent Corners

Secure tent corners with stakes, keeping the floor taut.

Assemble and Insert Frame Poles

Interlock shock-corded poles and insert them into center and side pole sleeves.

Connect Frame to Tent

Locate Pin & Ring Systems

Find the connection points on the tent for the frame poles.

Insert Frame Pole Ends

Connect one end of frame poles to the tent's Pin & Ring Systems.

Form Tent Arch

Apply pressure to poles to create an arch and insert the other end.

Attach Tent Frame Clips

Secure the tent frame by attaching clips to the poles.

Raise Ends of Tent

Connect Side Frame Poles

Attach the side frame poles to the tent's Pin & Ring Systems.

Create Tent Arches

Apply pressure to poles until they arch and fit into the pins.

Secure Tent Frame

Attach frame clips to the tent poles to secure the structure.

Attach Rainfly

Assemble Rainfly Poles

Interlock shock-corded poles for the rainfly.

Insert Rainfly Poles

Place rainfly poles into sleeves on the underside of the rainfly.

Drape and Secure Rainfly

Drape rainfly over tent, insert poles into grommets, and secure.

Attach and Stake Guylines

Connect guylines to rainfly loops and stake them out at an angle.

Important Tent Care and Safety

Manage Condensation

Minimize condensation via ventilation and removing wet items.

Proper Tent Storage

Dry tent before storage; do not store poles telescoped.

Safe Stake Removal

Remove stakes by pulling them directly, not by the tent fabric.

Flame Resistance Warning

Keep flame/heat sources away; fabric burns if exposed to flame.