To Next PageTo Next PageWhat to do if my Comet KR 1100 Pressure Washer motor suddenly stops?
If your Comet Pressure Washer motor suddenly stops, it might be due to the thermal relay being triggered by overheating. To resolve this, check the voltage, turn off the switch, and allow the motor to cool down for a few minutes.
Why is my Comet KR 1100 Pressure Washer pump running but not building pressure?
If your Comet Pressure Washer pump isn't generating pressure despite running, several issues could be the cause. First, check if the intake filter is clogged and clean it if necessary. Also, inspect the intake connection fitting and hose connectors for any air being drawn in. Furthermore, the inlet and outlet valves might be clogged or worn, requiring cleaning or replacement. Lastly, verify that the nozzle hole isn't too large and replace it if needed.
Why is there a loss of pressure in my Comet KR 1100 Pressure Washer?
If your Comet Pressure Washer experiences a loss of pressure, several factors could be responsible. Start by checking the nozzle for wear and replace it if necessary. Next, inspect the valves for dirt or clogs, cleaning or replacing them as needed. Also, examine the valve seals and other seals for wear, replacing them if necessary. Finally, check the filter for clogs and clean or replace it.
Why does my Comet Pressure Washer pump not run when I press the switch?
If your Comet Pressure Washer's pump isn't running when you press the switch, several things could be wrong. Start by checking the plug and fuses for any damage. Then, make sure the voltage is sufficient. If those aren't the problem, the pump might be locked, so try manually turning over the motor. Lastly, the thermal relay might have tripped, in which case you should let the motor cool down.
Why is the operating pressure of my Comet Pressure Washer irregular?
If your Comet Pressure Washer's operating pressure is irregular, it could be due to several reasons. Check the intake connectors for air being drawn in. Also, the valves may be clogged or worn, requiring cleaning or replacement. Similarly, worn seals can cause pressure irregularities, so inspect and replace them if necessary. Finally, ensure the motor stops completely after releasing the gun trigger before pressing it again.
Why is my Comet KR 1100 making excessive noise?
If your Comet Pressure Washer is making excess noise, it could be due to several factors. Check the intake lines for air being drawn in. Inspect the valves for wear, dirt, or clogs, and clean or replace them as needed. Also, examine the bearings for wear and replace them if necessary. Ensure that the water temperature is below 50 °C. Finally, check the filter for dirt and clean or replace it.
What to do if my Comet Pressure Washer motor hums but doesn't start?
If, when you press the switch on your Comet Pressure Washer, the motor hums but doesn't start, it could be due to a few reasons. Check that the mains voltage is at the specified level. Also, the pump might be blocked or frozen, so inspect it. Finally, the extension cable might be insufficient, so ensure it's adequate and replace it if necessary.
Why is the water from my Comet Pressure Washer mixed with oil?
If the expelled water from your Comet Pressure Washer is mixed with oil, it's likely that the sealing rings (water + oil) are worn. You should check and/or exchange them.
Why is my Comet KR 1100 Pressure Washer leaking water from the pump head?
If water leaks from the pump head of your Comet Pressure Washer, it's likely due to worn seals. You should exchange the seal or the O-ring of the seal set.
Why is my Comet Pressure Washer pump dripping?
If your Comet Pressure Washer pump is dripping, it's likely that the seals are worn. Check and replace them, preferably at a professional repair shop.
General| Brand | Comet |
|---|---|
| Model | KR 1100 |
| Category | Pressure Washer |
| Language | English |
Identifies the product as a cold water electric high pressure cleaner.
Essential safety regulations and accident prevention measures.
Step-by-step guide for connecting the hoses and accessories.
Procedure for starting the high pressure cleaner.
Guidance on proper handling and use of the cleaner during operation.
Steps to safely shut down the high pressure cleaner.
