2
W415-0803 / C / 04.19.12
TABLE OF CONTENTS
NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.
1.0 INSTALLATION OVERVIEW 3
2.0 INTRODUCTION 4
2.1 DIMENSIONS 5
2.1.1 BCDV36CF / BCDV36CFG 5
2.2 GENERAL INSTRUCTIONS 5
2.3 GENERAL INFORMATION 7
2.4 RATING PLATE INFORMATION 7
3.0 VENTING 8
3.1 VENTING LENGTHS AND COMPONENTS 8
3.2 TYPICAL VENT INSTALLATIONS 9
3.3 SPECIAL VENT INSTALLATIONS 11
3.3.1 PERISCOPE TERMINATION 11
3.3.2 CORNER TERMINATION 11
3.4 VENT TERMINAL CLEARANCES 12
3.5 VENT APPLICATION FLOW CHART 13
3.6 DEFINITIONS 13
3.7 ELBOW VENT LENGTH VALUES 14
3.8 TOP EXIT HORIZONTAL TERMINATION 14
3.9 REAR EXIT HORIZONTAL TERMINATION 16
3.10 TOP OR REAR EXIT VERTICAL TERMINATION 18
4.0 PRE-INSTALLATION PREPARATION 20
4.1 REMOVING THE VALVE ACCESS DOOR AND TOP DOOR TRIM 20
4.2 DOOR OPERATION 21
4.3 REAR EXIT 21
4.4 TOP VENT 21
5.0 INSTALLATION 22
5.1 WALL AND CEILING PROTECTION 22
5.2 HORIZONTAL INSTALLATION 23
5.3 VERTICAL INSTALLATION 23
5.4 USING FLEXIBLE VENT COMPONENTS 24
5.4.1 HORIZONTAL AIR TERMINAL INSTALLATION 24
5.4.2 VERTICAL AIR TERMINAL INSTALLATION 25
5.4.3 APPLIANCE VENT CONNECTION 26
5.5 USING RIGID VENT COMPONENTS 26
5.5.1 HORIZONTAL AIR TERMINAL INSTALLATION 26
5.5.2 EXTENDED HORIZONTAL AND CORNER TERMINAL INSTALLATION 26
5.6 VERTICAL THROUGH EXISTING CHIMNEY 27
5.6.1 VERTICAL AIR TERMINAL INSTALLATION 28
5.7 MOBILE HOME INSTALLATION 29
5.8 GAS INSTALLATION 29
5.9 OPTIONAL WALL SWITCH EXCLUDING BCDV36CFG 30
6.0 FRAMING 31
6.1 INSTALLING STAND-OFFS 32
6.2 MINIMUM FRAMING DIMENSIONS 33
6.2.1 STEEL HEADER INSTALLATION FOR CLEAN FACE SURROUND 34
6.3 MINIMUM ENCLOSURE CLEARANCES 35
6.3.1 REAR VENT ENCLOSURE 35
6.3.2 TOP VENT ENCLOSURE 36
6.3.3 ALCOVE ENCLOSURE 36
6.3.4 CLEAN FACE SURROUND MINIMUM ENCLOSURE CLEARANCES 37
6.4 CLEAN FACE SURROUND FRAMING AND FINISHING 38
6.4.1 FINISHED FLOOR INSTALLATION 38
6.4.2 HEARTH INSTALLATION 39
6.6 ALCOVE FRAMING 40
6.5 MINIMUM MANTEL CLEARANCES 40
7.0 FINISHING 41
7.1 DOOR INSTALLATION & REMOVAL 41
7.2 CLEAN FACE TRIM KIT INSTALLATION EXCLUDING GD36M 42
8.0 BCDV36CF FINISHING 43
8.1 LOG PLACEMENT 43
8.2 GLOWING EMBERS 44
8.3 CHARCOAL EMBERS 44
8.4 LOGO PLACEMENT 44
8.5 OPTIONAL ROCK KIT 44
9.0 BCDV36CFG FINISHING 45
9.1 GLASS BURNER INSTALLATION 45
9.2 TOP PRP PANEL INSTALLATION GD36M 46
10.0 OPTIONAL BLOWER INSTALLATION 47
10.1 ACCESSING THE BLOWER 47
11.0 WIRING DIAGRAM 48
11.1 BCDV36CFG LIGHT SWITCH 48
11.2 BCDV36CFG BURNER SWITCH 49
11.3 RECEPTACLE WIRING DIAGRAM 50
12.0 OPERATION 51
12.1 BCDV36CF 51
12.2 BCDV36CFG 52
To Next Page
Loading...
