Copystar CS-2550 - User Manual

SERVICE
MANUAL
Published in July ’05
2FT70943
Revision 3
CS-2550

Copystar CS-2550 Specifications

General

Brand	Copystar
Model	CS-2550
Category	All in One Printer
Language	English

Summary

Safety precautions

Safety warnings and precautions

Defines DANGER, WARNING, CAUTION symbols and their meanings.

1-1 Specifications

1-1-1 Specifications

Details machine specifications like type, size, speed, paper handling.

1-2 Handling Precautions

1-2-1 Drum

1-2-3 Installation environment

Specifies environmental requirements for machine installation.

1-3 Installation

1-3-1 Unpacking and installation

Outlines the step-by-step procedure for unpacking and installing the machine.

1-3-3 Installing the paper feeder (option)

Provides instructions for attaching the optional paper feeder to the MFP.

1-3-4 Installing the DP (option)

Guides the installation of the optional Document Processor (DP) unit.

1-3-5 Installing the duplex unit (option)

Details the process for installing the optional duplex unit.

1-3-6 Installing the drawer heater (option)

1-3-7 Installing the key counter (option)

1-3-8 Installing the finisher (option)

Guides the installation of the optional finisher.

1-3-9 Installing the job separator (option)

Details the process for installing the optional job separator.

1-3-10 Installing the fax system (option)

Explains how to install the optional fax system.

1-3-11 Installing the scan system (option)

Guides the installation of the optional scan system.

1-3-12 Installing the hard disk (option)

1-4 Maintenance Mode

1-4-1 Maintenance mode

Explains how to enter and execute maintenance items.

1-4-2 Management mode

Explains how to access and use the management mode for settings.

(1) Using the management mode

Explains how to access and use the management mode for settings.

(2) Setting the job accounting

Covers registering, deleting, and managing job accounts.

(3) Copy default

1-5 Troubleshooting

1-5-1 Paper misfeed detection

Explains how the machine detects paper misfeeds and indicates jam locations.

(1) Paper misfeed indication

Explains how misfeeds are indicated and reset.

(2) Paper misfeed detection conditions

Details conditions for misfeed detection with diagrams.

(3) Paper misfeeds

Lists problems, causes, and corrective measures for paper misfeeds.

1-5-3 Image formation problems

Details causes and corrective measures for various image formation issues.

(1) No image appears (entirely white).

(2) No image appears (entirely black).

(3) Image is too light.

1-5-4 Electric problems

Troubleshoots electrical issues such as non-operation or motor failures.

(1) The machine does not operate when the power switch is turned on.

Troubleshooting steps when the machine won't power on.

1-5-5 Mechanical problems

Addresses mechanical issues like paper feed, scanner travel, and jams.

(1) No primary paper feed.

Addresses issues with no primary paper feed, listing causes and solutions.

1-6 Assembly and Disassembly

1-6-1 Precautions for assembly and disassembly

Lists safety precautions before disassembly.

(1) Precautions

Lists safety precautions before disassembly.

1-6-2 Paper feed section

Details procedures for detaching and refitting paper feed components.

(1) Detaching and refitting the separation pulley

(2) Detaching and refitting the forwarding pulley and paper feed pulley

(3) Detaching and refitting the feed roller

(4) Detaching and refitting the drawer separation pulley

(5) Detaching and refitting the drawer forwarding pulley and drawer paper feed pulley

(6) Detaching and refitting the paper conveying unit

(7) Detaching and refitting the bypass paper feed pulley and bypass separation pad

1-6-3 Optical section

(5) Adjusting the longitudinal squareness (reference)

(6) Adjusting magnification of the scanner in the main scanning direction

Adjusts scanner magnification in the main scanning direction.

(7) Adjusting magnification of the scanner in the auxiliary scanning direction

Adjusts scanner magnification in the auxiliary scanning direction.

(8) Adjusting the scanner leading edge registration

Adjusts scanner leading edge registration for image errors.

(9) Adjusting the scanner center line

(10) Adjusting the margins for scanning an original on the contact glass

1-6-4 Drum section

1-6-7 Fixing section