EasyManua.ls Logo

Corken 291 - User Manual

Default Icon
100 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Model 491-107
Installation, Operation
& Maintenance Manual
Plain Style Compressors for Liquid
Transfer-Vapor Recovery
Solutions beyond products...
ORIGINAL INSTRUCTIONS IE101K
Warning: (1) Periodic inspection and maintenance of Corken products is essential. (2) Inspection, maintenance and installation of
Corken products must be made only by experienced, trained and qualified personnel. (3) Maintenance, use and installation of Corken
products must comply with Corken instructions, applicable laws and safety standards. (4) Transfer of toxic, dangerous, flammable or
explosive substances using Corken products is at user’s risk and equipment should be operated only by qualified personnel according
to applicable laws and safety standards.

Table of Contents

Questions and Answers

  • S
    Sharon HartAug 17, 2025
    Why is the capacity of my Corken 291 so low?
    • B
      Brenda MyersAug 17, 2025
      If your Corken Air Compressor has low capacity, several issues could be the cause. The valves might be broken, stuck, or leaking, in which case you should inspect and clean or repair them. A worn piston ring could also be the culprit, so inspect and replace it if necessary. Additionally, a clogged inlet strainer can restrict flow, so clean or replace the screen. Leaks in the piping can also reduce capacity; inspect and repair any leaks. Finally, ensure the 4-way control valve is lubricated by inspecting and lubricating it.
  • J
    jessicakennedyAug 20, 2025
    Why is my Corken 291 overheating?
    • M
      Monica WaltonAug 20, 2025
      If your Corken Air Compressor is overheating, several factors could be responsible. Start by checking the valves for any signs of damage, sticking, or leaks; inspect, clean, or repair them as needed. A worn piston ring can also cause overheating, so inspect and replace if necessary. A clogged inlet strainer can also lead to this issue, thus clean or replace the screen as necessary. Ensure that the cooling fins are clean, and clean them weekly. For issues such as high inlet or ambient temperature, high compression ratio, or an unbalanced load, it is recommended to consult the factory.
  • C
    Craig PhillipsAug 23, 2025
    What to do if my Corken Air Compressor has product leakage?
    • B
      Barry JonesAug 23, 2025
      If you're experiencing product leakage from your Corken Air Compressor, there are a few potential causes. Check for leaks in the piping and repair them as needed. A worn piston-rod packing can also cause leakage, so replace it. Loose valves, pistons, or packing can also be responsible; tighten or replace them as necessary. Additionally, a 4-way control valve that is not lubricated can lead to leakage; inspect and lubricate it.
  • I
    ipriceAug 26, 2025
    How to fix knocks, rattles, and noise in my Corken Air Compressor?
    • T
      Tyler HoustonAug 26, 2025
      Excessive noise in your Corken Air Compressor can stem from several sources. Valves that are broken, stuck, or leaking are a common cause; inspect, clean, or repair them. A loose flywheel or belt can also generate noise, so tighten them. If the wrist pin or wrist-pin bushing is worn, replace it. Similarly, a worn connecting-rod bearing should be replaced. An unbalanced load may also lead to noise, in this case inspect the valve or consult the factory.
  • B
    bridgesdanielAug 28, 2025
    How to reduce excessive vibration in my Corken 291 Air Compressor?
    • S
      Sandra MooreAug 28, 2025
      Excessive vibration in your Corken Air Compressor may be due to several reasons. Broken, stuck, or leaking valves can cause vibration, so inspect, clean, or repair them. A loose flywheel or belt can also lead to vibration, so ensure these are tightened. Worn wrist pins or wrist-pin bushings and worn connecting-rod bearings can also cause vibration and should be replaced. An unbalanced load may also be the cause, in this case inspect the valve or consult the factory. Inadequate compressor base can cause excessive vibration, so you should strengthen, replace, or grout it.
  • J
    Joann BrownAug 31, 2025
    What causes abnormal piston-ring wear in a Corken Air Compressor?
    • J
      Juan GillespieAug 31, 2025
      Abnormal piston-ring wear in your Corken Air Compressor can be attributed to several factors. Valves that are broken, stuck, or leaking can cause this issue, so inspect, clean, or repair them. A worn piston ring itself can also lead to abnormal wear, so inspect and replace it if necessary. Loose valves, pistons, or packing can contribute to this problem; tighten or replace them as needed. Dirty cooling fins can also cause abnormal wear, so clean them weekly. For issues such as high inlet or ambient temperature, high compression ratio, or an unbalanced load, it is recommended to consult the factory.
  • K
    Kathleen LopezSep 2, 2025
    Why is there oil in the cylinder of my Corken 291 Air Compressor?
    • K
      Kimberly JohnsonSep 3, 2025
      If you find oil in the cylinder of your Corken Air Compressor, it could be due to a worn piston-rod packing, which should be replaced. Alternatively, the valve, piston, or packing might be loose; tighten or replace these components as necessary.
  • C
    Cody MartinSep 8, 2025
    Why is product leaking through the crankcase breather of my Corken 291 Air Compressor?
    • N
      Nicole MyersSep 8, 2025
      If product is leaking through the crankcase breather of your Corken Air Compressor, it may be caused by a worn piston-rod packing, which requires replacement. Another potential cause is a loose valve, piston, or packing, which should be tightened or replaced as necessary.
  • J
    Jose JohnsonSep 12, 2025
    What causes oil leakage around the base of my Corken 291?
    • M
      Maria HillSep 12, 2025
      If you notice oil leakage around the base of your Corken Air Compressor, it could be due to leaking gas blowing oil from the crankcase, in which case you should tighten the packing. Another possibility is a bad oil seal, which would need to be replaced.
  • S
    Suzanne HarringtonSep 13, 2025
    What to do if my Corken 291 has no oil pressure?
    • L
      Lori RussellSep 14, 2025
      If your Corken Air Compressor has no oil pressure, it could be due to a lack of oil in the crankcase, in which case you should add oil. Alternatively, there may be an oil-pump malfunction, in which case you should see oil-pressure adjustment.

Summary

Introduction to Corken Compressors

Liquid Transfer By Vapor Differential Pressure

Explains how compressors transfer liquefied gases using pressure differences.

Residual Vapor Recovery Process

Describes the process of recovering residual vapors from a tank after liquid transfer.

Compressor Construction Features

Details the design and key components of the compressor for specific applications.

Installing Your Corken Compressor

Compressor Location Guidelines

Foundation Requirements

Requirements for a stable and proper foundation to ensure smooth operation.

Piping Design and Installation

Proper design and installation of piping to minimize vibration and ensure flow.

Liquid Traps for Protection

Importance and types of liquid traps to prevent compressor damage from liquid entry.

Crankcase Lubrication Recommendations

Relief Valve Installation

Requirements for relief valve installation at the compressor discharge for safety.

Shutdown and Alarm Devices

Essential safety devices like low oil pressure and high temperature switches.

Starting Up Your Corken Compressor

Flywheel and V-belt Alignment

Crankcase Oil Pressure Adjustment

How to set and verify the correct crankcase oil pressure for lubrication.

Comprehensive Startup Checklist

A list of checks to perform before and after starting the compressor.

Routine Service and Repair Procedures

Valve Inspection and Service

Procedures for inspecting, cleaning, and replacing suction and discharge valves.

Piston Ring and Expander Replacement

Bearing Replacement Procedures

Appendix A: Model Number Identification

Appendix B: Compressor Specifications

Specifications for Vertical Single-Acting Models

Specifications for Vertical Double-Acting Models

Appendix C: Compressor Selection

Troubleshooting Compressor Issues

Corken 291 Specifications

General IconGeneral
Model291
CategoryAir Compressor
Cooling MethodAir Cooled
Power SourceElectric
LubricationLubricated

Related product manuals