What to do if the DRINKS ARE FOAMY in Cornelius Dispenser?
If the drinks from your Cornelius Dispenser are foamy: * Clean and sanitize the nozzle & syrup diffuser. * Clean and sanitize the bulk coke tank, if needed. * Replace or switch to a backup CO2 tank if the CO2 is low or out. * Ensure the jumper hose on the bulk tank is connected when changing bulk tanks.
What causes CONVEYOR STALLED in Cornelius Dispenser?
If the conveyor in your Cornelius Dispenser is stalled, it's likely due to a cup jammed in the conveyor at the cup extraction position. Remove all cups from the conveyor cup holders at the EXTRACT POSITION before pressing the ENTER button. Make sure the conveyor is installed correctly. Repair or replace if necessary.
What to do if the Cornelius Dispenser has low water pressure?
If you're experiencing low water pressure with your Cornelius Dispenser, there are several potential causes and solutions: * If the water supply line is excessively long (over 40 ft.) and 3/8” in diameter, increase the line size to 1/2”. * If the water pressure is generally low, consider adding a water pressure booster pump. * If the water filter is plugged, change it. * If the water booster bladder has burst, replace the water booster tank/bladder.
What causes slushy ice in my Cornelius Dispenser?
Slushy ice or water in the hopper of your Cornelius Dispenser can be caused by: * Blocked drains in the cold plate. To resolve this, remove the access covers in the cold plate cover and inspect/clean the drains. * Poor ice quality due to water quality or ice maker problems. Correct the water quality or repair the ice maker.
How to fix a blown fuse in Cornelius Dispenser?
A blown fuse or circuit breaker in your Cornelius dispenser could be due to: * A short circuit in the electrical wiring. In this case, repair the wiring. * An inoperable agitator motor (shorted motor). If this is the cause, replace the gear motor.
What to do if the Cornelius ABS 2.0 Commercial Food Equipment conveyor is stalled?
If the conveyor in your Cornelius Commercial Food Equipment is stalled, it's likely due to a cup jammed in the conveyor at the cup extraction position, preventing both the conveyor and turret from operating. To resolve this, remove all cups from the conveyor cup holders at the EXTRACT POSITION, then press the ENTER button to allow another cup to be extracted and dispensing to continue. Also, ensure the conveyor is correctly installed and repair or replace if necessary.
Why is the air or CO2 low or out in my Cornelius ABS 2.0?
If the air or CO2 is low or out in your Cornelius Commercial Food Equipment, it may be because the CO2 supply is low or empty, or the air compressor is not operating. Change the CO2 cylinder or have the bulk tank refilled. Check why the air compressor is not operating and repair it.
What to do if the Cornelius Commercial Food Equipment shows a clear cup jam?
If the Cornelius Commercial Food Equipment displays a 'CLEAR CUP JAM' error, it means a cup is stuck in the conveyor at the extraction point, preventing the conveyor and turret from working. First, remove all cups from the conveyor cup holders at the Extract Position, and then press the ENTER button. This should allow another cup to be extracted and dispensing to continue. Also, avoid over-stacking cups in the cup tubes (do not fill above the top), check if the cup tube fingers are damaged (replace if bent), ensure cup tubes are properly mounted (remove and remount if necessary), and verify all hardware is present on the cup tubes (replace any missing hardware).
How to fix A. Ice Chute not installed correctly in Cornelius Dispenser?
If the ice chute is not installed correctly in your Cornelius Dispenser, reinstall it.
What causes NO CUP EXTRACTED in Cornelius Dispenser?
If your Cornelius Dispenser is showing 'NO CUP EXTRACTED', it could be due to: * The gripper failing to extract a cup from the cup tube. Check the cup supply at the extract station to ensure cups aren't stuck and that gripper pads aren't damaged. * Wet grabber pads. Dry them off, and replace them if damaged. * Empty CO2. Check the bulk CO tank, and if empty, switch to the backup CO and turn it on. * Damaged cup tube fingers. If damaged, replace all four fingers. * Cups that are packed together and will not separate.
General| Brand | Cornelius |
|---|---|
| Model | ABS 2.0 |
| Category | Commercial Food Equipment |
| Language | English |
To Next Page
