What to do if my Craftsman 137.212372 motor does not start?
If the Craftsman Saw motor does not start, check the electrical power at the outlet to ensure that the fuse hasn't blown or the circuit breaker hasn't tripped on the home panel. Another reason may be worn brushes, which you should replace. It is also possible that there is a limit switch failure, so replace the limit switch.
Why does my Craftsman 137.212372 blade bind, jam, or burn wood?
If the Craftsman Saw blade binds, jams, or burns wood, it could be due to several reasons. You might be using the saw improperly, so review the BASIC SAW OPERATION section. The blade could be dull or warped, requiring replacement or sharpening. It's also possible the blade is the wrong size; replace it with a 10-inch diameter blade. Finally, make sure the wood isn't moving during the cut; use a hold-down clamp to secure the workpiece to the table.
Why does my Craftsman 137.212372 Saw vibrate or shake?
If your Craftsman Saw vibrates or shakes, it could be due to a blade that is not round, damaged, or loose, requiring you to replace the blade. Alternatively, the arbor bolt might be loose, so you should tighten it.
Why doesn't the brake stop the blade within 6 seconds on my Craftsman Saw?
If the brake on your Craftsman Saw doesn't stop the blade within 6 seconds, several issues could be the cause. The motor brushes might not be seated correctly or are sticking, so inspect, clean, or replace them. The motor brake may have overheated due to using a defective or wrong-sized blade, or from rapid on/off cycling, so use a recommended blade and let the saw cool down. It's also possible the arbor bolt is loose, so retighten it. Lastly, the brushes could be cracked or damaged, so replace them.
What to do if the cutting arm will not fully raise, or blade guard won’t fully close on my Craftsman 137.212372 Saw?
If your Craftsman Saw cutting arm will not fully raise, or the blade guard won’t fully close, it could be due to a pivot bolt that is too tight, so loosen the pivot bolt lock nut. Also, sawdust build-up might be the reason; see the MAINTENANCE section.
Why is the cutting arm wobbling on my Craftsman Saw?
If the cutting arm wobbles on your Craftsman Saw, the pivot points may be loose, so see the ADJUSTMENT - Cutting Arm Travel section.
Why is the angle of cut not accurate on my Craftsman 137.212372 Saw?
If the angle of the cut is not accurate and you cannot adjust the miter on your Craftsman Saw, the miter table might be unlocked, so see the OPERATION - Miter Angle Adjustment section. Also, there might be sawdust under the table; vacuum or blow out the dust, and be sure to WEAR EYE PROTECTION.
What to do if the blade hits the table on my Craftsman 137.212372 Saw?
If the blade hits the table on your Craftsman Saw, there might be a misalignment, so see the ADJUSTMENT - Cutting Arm Travel section.
Why do the brushes spark when the switch is released on my Craftsman Saw?
If the brushes spark when the switch is released on your Craftsman Saw, the brushes may be worn, so replace them. See MAINTENANCE section.
Details the technical specifications of the miter saw, including motor, blade, and cutting capacities.
Explains warning icons and safety alert symbols for hazard identification and safe operation.
Essential safety rules for operating power tools, covering personal protection and work area.
Crucial safety instructions unique to this miter saw, focusing on blade handling and operational practices.
Guidelines for safe electrical connections, circuit protection, and handling of double-insulated tools.
Lists necessary tools for assembly and identifies all items included in the product packaging.
Step-by-step instructions for assembling the miter saw components, including head, handle, and accessories.
Procedures for securely mounting the miter saw to a workbench or stand for stable operation.
Detailed instructions for adjusting bevel stops, miter angles, and fence squareness for precise cuts.
Steps to align the laser guide with the saw blade for precise cut preview and positioning.
General guidelines for safe and effective operation before and during saw use.
Guides on making basic cuts, miter cuts, bevel cuts, and compound cuts with the miter saw.
Instructions for cutting wide boards, bowed material, grooves, and molding using the miter saw.
Procedures for cleaning, lubricating, and replacing worn parts like carbon brushes to ensure proper function.
Solutions for common motor and saw operation problems, including troubleshooting steps and corrective actions.
Comprehensive list of all parts with identification numbers and quantities, including schematic views.
Information on repair protection plans, customer care hotlines, and product registration.
To Next Page
General