To Next PageTo Next PageWhat to do if my Craftsman MiterMate 137.212260 motor does not start?
If the Craftsman Saw motor doesn't start, there are a few potential causes. First, the limit switch may have failed, requiring a replacement. Second, the brushes could be worn, also requiring replacement. Finally, check to ensure there is electrical power at the outlet, as a fuse may have blown or a circuit breaker tripped.
Why does the blade on my Craftsman MiterMate 137.212260 bind, jam, or burn the wood?
The blade on your Craftsman Saw might bind, jam, or burn wood due to several reasons. It could be due to improper operation. The blade might be dull or warped, requiring replacement or sharpening. Using the wrong blade size can also cause this issue, so replace it with a 10-inch diameter blade. Also, make sure that the wood is not moving during the cut, use a clamp to secure the workpiece to the fence unit and table.
How to fix a Craftsman MiterMate 137.212260 when the brake does not stop the blade within 6 seconds?
If the brake on your Craftsman Saw doesn't stop the blade within 6 seconds, several factors could be at play. The motor brushes might be lightly sticking, requiring inspection, cleaning, or replacement. The motor brake could be overheated from using a defective or wrong-sized blade, or from rapid on/off cycling; use a recommended blade and allow the saw to cool down. A loose arbor bolt could also be the culprit, so retighten it. Finally, the brushes might be cracked or damaged, in which case they should be replaced.
Why does my Craftsman Saw vibrate or shake?
If your Craftsman Saw vibrates or shakes, it could be due to a saw blade that is not round, damaged, or loose; in this case, replace the blade. Another potential cause is a loose arbor bolt; tighten the arbor bolt to resolve this.
What to do if the angle of cut is not accurate on my Craftsman MiterMate 137.212260 and I can't adjust the miter?
If the angle of cut is not accurate on your Craftsman Saw and you cannot adjust the miter, it could be because the miter table is unlocked. Also, sawdust under the table can cause this issue. Vacuum or blow out the dust, and be sure to wear eye protection.
Why does my Craftsman MiterMate 137.212260 brush spark when the switch is released?
If the brush sparks when the switch is released on your Craftsman Saw, it could be that the brush is worn. In this case, replace the brushes.
What to do if the cutting arm will not fully raise, or blade guard won’t fully close on my Craftsman Saw?
If the cutting arm will not fully raise, or the blade guard won’t fully close on your Craftsman Saw, it could be that the pivot spring was not replaced properly after service. Clean and lubricate moving parts.
Identifies the Craftsman MiterSaw model and provides an overview of included sections.
Provides contact information for technical support and parts/repair services.
Details the terms and conditions of the Craftsman full warranty for the miter saw.
Alerts users to potential health hazards from dust exposure in California.
Details the electrical specifications of the motor and the size of the saw blade.
Outlines the rotating table features and the maximum cutting capacities of the miter saw.
Provides critical safety information regarding power supply and circuit protection for the tool.
Illustrates and explains various warning icons used in the manual for safety.
Defines DANGER, WARNING, and CAUTION labels to indicate potential risks.
Covers essential safety practices to follow before and during the operation of the power tool.
Provides fundamental safety instructions for operating any power tool.
Emphasizes wearing proper apparel, eye protection, and maintaining a clean work area.
Covers tool care, risk reduction, and specific hazards like dust and electronic device interference.
Provides specific safety instructions for using the compound miter saw, including blade and guard usage.
Details safe handling of the workpiece, blade checks, and operation procedures to prevent accidents.
Covers restrictions on cutting materials, use in hazardous areas, and proper tool shutdown.
Instructions for securing the tool, cleaning the work area, and handling damaged parts.
Details power requirements, plug types, and the benefits of double insulation for electrical safety.
Explains how to protect the motor from damage and issues related to starting and stalling.
Guides on proper circuit protection, fuses, and selecting the correct extension cords for the saw.
Provides a chart to determine the minimum wire gauge for extension cords based on ampere rating and length.
Guidelines for using recommended accessories and warnings against improper use or modifications.
Specific warnings and safety precautions related to the use and handling of carbide-tipped saw blades.
Lists the tools supplied with the saw and those that are not supplied but needed for assembly.
Instructions on how to check if a combination square is true for accurate assembly.
Steps for safely unpacking the miter saw from its carton and identifying all parts.
Guidance on what to do if any parts are missing or damaged before assembly.
A labeled diagram identifying all the major parts and components of the miter saw.
Provides definitions for technical terms starting with letters A through O used in the manual.
Provides definitions for technical terms starting with letters P through W used in the manual.
Explains woodworking terminology relevant to the operation and features of the miter saw.
Instructions for raising, lowering, and locking the cutting head of the miter saw.
Steps for installing the dust bag and the workpiece clamp onto the miter saw.
Details on storing the angle finder and the blade wrench conveniently on the saw.
Step-by-step instructions for safely removing and installing the saw blade.
Detailed steps for correctly installing a new saw blade, including safety warnings.
Instructions for securely mounting the miter saw to a workbench or a portable base.
Procedures for adjusting the bevel stop and ensuring the blade is at a 90° angle to the table.
Steps to adjust the saw's bevel to 45° and set the miter angles using the sliding fence units.
Guides on ensuring the sliding fence units are square and aligned correctly with the blade.
Instructions for adjusting lock levers and the cutting arm's downward travel depth.
Details on how to adjust and use the workpiece clamp for securing materials.
Essential safety instructions and inspection steps to perform before using the miter saw.
Covers learning controls, checking guards, and general operational procedures.
Guidance on keeping the work area clean, planning cuts, dressing safely, and inspecting the workpiece.
Specifies materials that can and cannot be cut with the miter saw to prevent hazards.
Details on safe cutting practices, avoiding kickback, freehand cutting, and handling large workpieces.
Safety advice for cutting non-ferrous metals and precautions when the saw is running.
Guidance on proper body and hand placement for safe and effective miter saw operation.
Instructions on how to turn the laser guide on and off for precise cutting alignment.
Details on laser guide calibration, safety warnings, and potential hazards from laser radiation.
Steps to safely start the miter saw, including engaging the lock-off switch.
Instructions for setting up and performing miter cuts using the sliding fence units.
Guides on performing bevel cuts and compound cuts, including fence and head adjustments.
Instructions for using the stop plate to support workpieces for repetitive cutting tasks.
Steps to use the angle finder to copy corner angles for accurate setup.
Procedure to adjust sliding fences to match angles copied by the angle finder.
Detailed guide on cutting crown molding accurately using the miter saw.
Charts illustrating orientations for cutting crown molding for various corner types.
Instructions for setting up and cutting base molding using the miter saw.
Alternative method for cutting base molding, especially for pieces too large for standard features.
Alternative method for cutting crown molding when workpiece size exceeds standard capabilities.
Chart providing specific bevel and miter settings for various crown molding cuts.
Tables providing precise miter and bevel angle settings for different wall angles and molding types.
Instructions for inspecting and replacing worn carbon brushes in the motor.
Guidance on cleaning and maintaining the lower blade guard and emptying the sawdust bag.
Details on where and how to lubricate specific pivot points on the miter saw.
Guidance on checking and adjusting the table lock levers for proper clamping.
Common motor problems, their causes, and suggested corrective actions.
Troubleshooting guide for issues related to blade performance and cutting accuracy.
List of parts for Saw Schematic A, including ID, description, size, and quantity.
Exploded view diagram illustrating the parts listed in Schematic A.
List of parts for Saw Schematic B, including ID, description, size, and quantity.
Exploded view diagram illustrating the parts listed in Schematic B.
List of parts specific to the motor assembly, including ID, description, size, and quantity.
Exploded view diagram illustrating the motor assembly and its components.
Details the coverage, benefits, and services offered by Craftsman Repair Protection Agreements.
Provides contact numbers and websites for Sears services, parts, and support.
General