Craftsman 247.11683 - User Manual

Questions and Answers

D
David TaylorAug 7, 2025
Why won't my Craftsman Snow Blower engine start?
- B
  briannovakAug 7, 2025
  Your Craftsman Snow Blower might not start due to several reasons: * The fuel tank may be empty or contain stale fuel. Refill it with clean, fresh gasoline. * The key may not be fully inserted. Ensure the key is inserted all the way. * The spark plug wire might be disconnected. Connect the wire to the spark plug. * The spark plug could be faulty. Try cleaning it, readjusting the gap, or replacing it. * The engine may not be primed. Push the engine primer button five to seven times. * The engine might be flooded from excessive priming. Wait at least ten minutes before attempting to start it again.
E
ericaclarkAug 11, 2025
What to do if my Craftsman Snow Blower unit fails to discharge snow?
- S
  Shane AllenAug 11, 2025
  If your Craftsman snow thrower isn't discharging snow, here's what you can do: * The chute assembly might be clogged. Stop the engine, disconnect the spark plug wire, and then clean the chute and the inside of the auger housing using a clean-out tool or a stick. * A foreign object might be lodged in the auger. Immediately stop the engine, disconnect the spark plug wire, and remove the object from the auger. * The auger control cable may be out of adjustment. Adjust the auger control cable. * The auger belt could be loose or damaged. Replace the auger belt.
L
Laura JohnsonAug 16, 2025
Why does my Craftsman 247.11683 Snow Blower engine run erratically?
- T
  timothy18Aug 16, 2025
  An erratic engine in your Craftsman Snow Blower could stem from: * The engine running on choke. Move the choke control to the RUN position. * Water or dirt in the fuel system. Run the engine until the fuel tank is empty and then refill it with fresh fuel.
H
Heather SmithAug 20, 2025
What causes loss of power in my Craftsman 247.11683 Snow Blower?
- L
  Logan WadeAug 20, 2025
  Loss of power in your Craftsman Snow Blower may be due to: * A loose spark plug wire. Firmly connect the spark plug wire. * A plugged vent in the gas cap. Clear the vent.
M
Michael MasseyAug 25, 2025
What to do if my Craftsman 247.11683 Snow Blower has excessive vibration?
- L
  lisahamiltonAug 26, 2025
  If your Craftsman snow thrower is vibrating excessively: * Loose parts or a damaged auger could be the cause. Immediately stop the engine and remove the key. Check for any visible damage, and tighten all bolts and nuts. Repair as needed. If the problem continues, seek professional assistance.
T
Thomas WestAug 29, 2025
Why doesn't my Craftsman 247.11683 Snow Blower self-propel?
- B
  Brian MaloneAug 29, 2025
  Your Craftsman snow thrower might fail to self-propel because: * The auger control cable is out of adjustment. Adjust the auger control cable as shown in the Service and Maintenance section. * The auger drive belt is loose or damaged. Replace the auger drive belt.
T
Teresa PotterSep 2, 2025
Why does the Craftsman 247.11683 auger continue to rotate?
- B
  Brandi AdamsSep 2, 2025
  The auger on your Craftsman snow thrower might keep rotating because the auger control cable is out of adjustment. Adjust the auger control cable as shown in the Service and Maintenance section.

Craftsman 247.11683 Specifications

General

Engine Type	4-cycle OHV
Engine Displacement	208cc
Starting System	Electric Start
Intake Height	21 inches
Drive Type	Self-propelled
Auger Material	Steel
Chute Control	Manual