Craftsman 247.88955 - User Manual

Questions and Answers

J
James MarksAug 10, 2025
Why won't my Craftsman 247.88955 Snow Blower engine start?
- J
  Joann AshleyAug 11, 2025
  Your Craftsman Snow Blower engine may fail to start due to several reasons: * The choke control might not be in the ON position; if so, move it to the ON position. * The spark plug wire could be disconnected; connect it to the spark plug. * The spark plug might be faulty; clean, adjust the gap, or replace it. * The fuel tank may be empty or contain stale fuel; fill it with clean, fresh gasoline. * The engine may not be primed; prime it as instructed in the Operation Section. * The safety key might not be inserted; insert it fully into the switch.
M
Michelle HarringtonAug 16, 2025
What to do if my Craftsman 247.88955 unit fails to discharge snow?
- M
  Mary BrownAug 16, 2025
  If your Craftsman Snow Blower fails to discharge snow, here are some possible solutions: * The chute assembly might be clogged. Stop the engine immediately, disconnect the spark plug wire, and clean the chute assembly and inside of the auger housing with a clean-out tool or a stick. * A foreign object may be lodged in the auger. Stop the engine immediately, disconnect the spark plug wire, and remove the object from the auger with a clean-out tool or a stick. * The auger cable might need adjustment. Adjust the auger control cable according to the Assembly section. * The auger belt could be loose or damaged. Replace the auger belt, referring to the Service and Maintenance section. * The shear pins might be sheared. Replace them with new shear pins.
S
Susan WagnerAug 20, 2025
Why does my Craftsman 247.88955 Snow Blower engine run erratically?
- M
  Michael SingletonAug 20, 2025
  An erratic running Craftsman Snow Blower engine can be caused by: * The engine running on CHOKE; move the choke control to the OFF position. * Stale fuel; replace with clean, fresh gasoline. * Water or dirt in the fuel system; drain the fuel tank and refill with fresh fuel. * The carburetor being out of adjustment; in this case, contact your Sears Parts & Repair Center.
M
Michelle NguyenAug 26, 2025
What to do if my Craftsman 247.88955 Snow Blower loses power?
- S
  sullivanbryceAug 26, 2025
  If your Craftsman Snow Blower is losing power: * Check the spark plug wire and ensure it is connected and tightened. * Inspect the gas cap vent hole for blockage from ice or snow, and clear it to ensure proper ventilation.
C
Carol ShawAug 30, 2025
How to fix excessive vibration in my Craftsman Snow Blower?
- J
  John BrownAug 30, 2025
  If your Craftsman Snow Blower is vibrating excessively, stop the engine immediately, disconnect the spark plug wire, and check for loose parts or a damaged auger. Tighten all bolts and nuts. If the vibration continues, have the unit serviced by a Sears Parts & Repair Center.
K
karinaharrisSep 4, 2025
Why won't my Craftsman Snow Blower propel itself?
- J
  Justin MillerSep 4, 2025
  If your Craftsman Snow Blower isn't moving on its own, it could be due to: * The drive cable needing adjustment; adjust the drive control cable as described in the Service and Maintenance section. * A loose or damaged drive belt; replace the drive belt, consulting the Service and Maintenance section. * A worn friction wheel; replace the friction wheel.

Craftsman 247.88955 Specifications

General

Engine Type	4-cycle OHV
Engine Displacement	208cc
Intake Height	21 inches
Drive System	Self-propelled
Speed Settings	6 forward, 2 reverse
Auger Material	Steel
Chute Rotation	200 degrees
Stages	Two-stage
Start Type	Electric / Recoil
Starter Type	Electric Start
Clearing Width	24 inches