To Next PageTo Next PageHow to fix Craftsman 316.380180 that won't idle?
If the engine of your Craftsman chainsaw will not idle, several factors could be responsible. A dirty air filter can cause this, so clean or replace it. Old or improperly mixed fuel is another possibility; drain the fuel tank and add fresh, properly mixed fuel. Finally, the idle speed might be incorrect, so adjust it accordingly.
Why is my Craftsman 316.380180 Chainsaw smoking?
If the guide bar and saw chain of your Craftsman chainsaw are running hot and smoking, it could be due to several reasons. Check if the saw chain tension is too tight and adjust it accordingly. Ensure the chain oil reservoir is full; if not, refill it. Also, the guide bar groove and oil passages might be dirty, so clean them. Lastly, the automatic oiler flow might be too low; try increasing the oil flow.
What to do if Craftsman 316.380180 Chainsaw won't accelerate?
If your Craftsman chainsaw engine will not accelerate, it may be due to the fuel being old (over 30 days) or improperly mixed; drain the fuel tank and add fresh, properly mixed fuel. Alternatively, a dirty air filter could be the cause; clean or replace the air filter to resolve this.
Why Craftsman 316.380180 Chainsaw rotates, but does not cut?
If the saw chain on your Craftsman chainsaw rotates but doesn't cut, there are a couple of things to check. First, the saw chain might be dull, so sharpen or replace it. Second, make sure the saw chain isn't on backwards; check and correct the direction if needed.
Why does my Craftsman chainsaw lack power?
If your Craftsman chainsaw engine lacks power or stalls, the issue could stem from a few causes. Old or improperly mixed fuel is a common culprit, so drain the tank and refill it with fresh, properly mixed fuel. A dirty air filter can also cause this problem, so clean or replace it. Lastly, a faulty spark plug might be the reason; in that case, refer to the section on maintaining the spark plug.
What to do if Craftsman chainsaw chain won't rotate?
If the saw chain on your Craftsman chainsaw does not rotate, several factors could be at play. Check if the chain brake is engaged and disengage it. The saw chain tension might be too tight, so adjust it. Inspect the guide bar and saw chain for damage and replace them if necessary. Also, the guide bar and saw chain might be assembled incorrectly, so refer to the section on removing and installing them. Finally, the drive assembly could be damaged; refer to the service information for further assistance.
General| Bar Length | 18 inches |
|---|---|
| Engine Displacement | 42 cc |
| Chain Pitch | 3/8 inch |
| Chain Gauge | 0.050 inch |
| Type | Gasoline |
Safety guidelines for operating gas-powered units, focusing on fuel handling and potential hazards.
Precautions and best practices for operating the chainsaw safely and effectively.
Explains the causes and nature of chainsaw kickback to help reduce surprise and injury.
Steps to minimize the risk of kickback injuries, emphasizing proper grip and technique.
Describes the intended uses of the chainsaw, such as felling, bucking, and pruning.
Lists the tools needed for assembling the chainsaw.
Details the safety mechanisms built into the chainsaw for user protection.
Lists part numbers and descriptions for common replacement components.
Instructions for filling the chain oil reservoir before first use.
Guidance on properly tensioning the saw chain before operation.
Procedure to verify the correct functioning of the chain brake system.
Step-by-step guide on how to safely refuel the chainsaw.
Detailed steps on how to safely start the chainsaw engine.
Procedures for safely shutting down the chainsaw engine.
Methods for immediate shutdown in emergency situations.
Advice for achieving optimal performance and efficient cutting.
Instructions on the correct grip and stance for safe operation.
Fundamental techniques for making cuts with the chainsaw.
Step-by-step guide for safely cutting down trees.
Instructions for cutting logs into desired lengths safely.
Outlines recommended maintenance tasks and their frequency.
Details the user's role in maintaining the unit.
How to control the amount of oil delivered to the chain.
Tips for keeping the saw chain in good condition.
Procedure for lubricating the sprocket tip to ensure smooth operation.
Instructions for cleaning and maintaining the air filter.
Steps for inspecting, cleaning, and replacing the spark plug.
Procedures for cleaning the chainsaw after use.
Guidelines for storing the chainsaw, including long-term storage.
