Craftsman C459-52306 - User Manual

64 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

Sears Canada Inc., 290 Yonge Street, Toronto, On M5B 2C3

Visit our web site: sears.ca

CAUTION: Before using

this product, read this

manual and follow all

safety rules and operating

instructions.

Operator’s Manual

22” SNOW THROWER

Model No. C459-52306

• SAFETY

• ASSEMBLY

• OPERATION

• MAINTENANCE

• PARTS LIST

®

8/15/13

769-09243

Table of Contents

Questions and Answers

K
Kenneth MathewsAug 17, 2025
Why is my Craftsman Snow Blower engine running erratically?
- S
  shane74Aug 17, 2025
  An erratic engine in your Craftsman Snow Blower can stem from a few issues: * The engine may be running on choke. Move the choke lever to the RUN position. * The fuel line might be blocked, or the fuel could be stale. Clean the fuel line and fill the tank with fresh, clean gasoline. * There could be water or dirt in the fuel system. Run the engine until it stops, then refill with fresh fuel.
D
David HinesAug 22, 2025
What to do if my Craftsman Snow Blower loses power?
- H
  hallbillyAug 22, 2025
  If your Craftsman Snow Blower is losing power, consider these potential causes: * The spark plug wire may be loose. Connect and tighten the spark plug wire. * The gas cap vent hole might be plugged. Remove any ice and snow from the gas cap, ensuring the vent hole is clear.
C
Cynthia RayAug 29, 2025
Why does my Craftsman C459-52306 Snow Blower have excessive vibration?
- J
  Jennifer BlackAug 29, 2025
  Excessive vibration in your Craftsman Snow Blower is likely due to loose parts or a damaged auger. Stop the engine immediately and disconnect the spark plug wire. Tighten all bolts and nuts.
W
William JamesSep 3, 2025
What to do if my Craftsman Snow Blower unit fails to discharge snow?
- B
  Brandon JamesSep 3, 2025
  If your Craftsman Snow Blower isn't discharging snow, here's what you can check: 1. The chute assembly might be clogged. Stop the engine immediately, disconnect the spark plug wire, and clean the chute assembly and the inside of the auger housing with a clean-out tool or a stick. 2. There could be a foreign object lodged in the auger. Stop the engine immediately, disconnect the spark plug wire, and remove the object from the auger using a clean-out tool or a stick. 3. The shear pins might be sheared. Replace them with new shear pins.
M
montgomerybrittanyNov 10, 2025
Why does my Craftsman C459-52306 Snow Blower engine fail to start?
- P
  Patricia SimpsonNov 10, 2025
  There are several reasons why your Craftsman Snow Blower engine might not be starting: * The choke control may not be in the Choke position. If this is the case, move the choke control to the Choke position. * The spark plug wire might be disconnected. Ensure the wire is securely connected to the spark plug. * The spark plug could be faulty. Try cleaning, adjusting the gap, or replacing the spark plug. * The fuel tank may be empty or contain stale fuel. Refill the tank with clean, fresh gasoline. * The engine might not be primed. Prime the engine as instructed in the Operation Section. * The safety key might not be inserted. Insert the key fully into the switch. * If using the electric start, the extension cord may not be connected. Connect one end of the extension cord to t...

Craftsman C459-52306 Specifications

General

Clearing Width	26 in.
Auger Material	Steel
Engine Displacement	98cc
Starter Type	Recoil
Drive System	Friction disc
Chute Control	Manual
Skid Shoes	Adjustable
Warranty	2 years

Related product manuals

Craftsman C459-52310

Craftsman C459-52102

Craftsman C459-52104

Craftsman C459-52415

Preview: Craftsman C459-52413

Craftsman C459-52413

Craftsman C459-52213

Craftsman C459-52216

Craftsman C459-52106

Craftsman C459-52215

Preview: Craftsman C459-52401

Craftsman C459-52401

Craftsman C459-52222

Preview: Craftsman C459-527870

Craftsman C459-527870