Craftsman WC215 User Manual (English)

Questions and Answers:

D
David PhillipsAug 4, 2025
How to start a Craftsman WC215 Trimmer if it won't start?
- S
  Sandra RobinsonAug 4, 2025
  If your Craftsman Trimmer engine won't start, there are several possible causes: * The fuel tank may be empty, in which case you should fill it with properly-mixed fuel. * You may not have pressed the primer bulb enough; try pressing it 10 times. * The engine might be flooded; press the throttle lockout, squeeze the throttle control, and pull the starter rope until the engine starts. * The fuel could be old (over 30 days) or improperly mixed; drain the tank and add fresh, properly-mixed fuel. * The spark plug might be fouled, requiring replacement. * The choke lever may not have been flipped. Refer to the Starting Instructions in the Starting and Stopping section.
T
Tommy LesterAug 9, 2025
Why does my Craftsman WC215 engine lack power or stall?
- J
  Joshua WilsonAug 9, 2025
  If your Craftsman Trimmer engine lacks power or stalls, it could be due to several reasons. The fuel might be old (over 30 days) or improperly mixed, in which case you should drain the fuel tank and add fresh, properly-mixed fuel. Another possibility is a dirty air filter, which requires cleaning or replacement. Lastly, a fouled spark plug can also cause this issue, so consider replacing it.
T
Teresa RoseAug 13, 2025
Why won't my Craftsman WC215 engine idle?
- D
  Debbie ReedAug 14, 2025
  If your Craftsman Trimmer engine will not idle, there are a few potential causes. The air filter may be dirty, so you should clean or replace it. The fuel might be old (over 30 days) or improperly mixed; in this case, drain the fuel tank and add fresh, properly-mixed fuel. Additionally, the idle speed could be incorrect, requiring adjustment.
S
Susan KingAug 19, 2025
What to do if the cutting line advances uncontrollably on my Craftsman WC215 Trimmer?
- M
  Michael OdomAug 19, 2025
  If the cutting line on your Craftsman Trimmer advances uncontrollably, it's likely due to oil, cleaner, or lubricant being present in the cutting head. To resolve this, clean the cutting head thoroughly.
B
Bobby ScottAug 25, 2025
Why won't the cutting head advance line on my Craftsman WC215?
- J
  Joan SmithAug 25, 2025
  If the cutting head on your Craftsman Trimmer will not advance line, several issues could be the cause. The cutting head might be bound with grass, so stop the engine and clean it. The cutting head could be out of line, requiring you to refill it with new line. The inner reel might be bound up, so clean the inner reel and outer spool. The cutting head may be dirty, so open it and remove any welded sections. The line could be welded, in which case you should rewind it. The line might be twisted; stop the unit, push the bump knob, and pull the line until 4 inches (102 mm) extends outside the cutting head. Finally, not enough line might be extended, so clean and thoroughly dry the cutting head.
W
wendymillerAug 28, 2025
What to do if my Craftsman WC215 engine will not accelerate?
- M
  Michael WatsonAug 28, 2025
  If your Craftsman Trimmer engine will not accelerate, it could be due to old or improperly mixed fuel (over 30 days old). Drain the fuel tank and add fresh, properly-mixed fuel. Another cause could be the cutting head being bound with grass; stop the engine and clean the cutting head. A dirty air filter can also prevent acceleration, so clean or replace it.

Craftsman WC215 Specifications

General

Brand	Craftsman
Model	WC215
Category	Trimmer
Language	English

Summary

SAFETY

SPARK ARRESTOR NOTE

Note regarding spark arrestor requirements for specific U.S. forest lands and states.

CALIFORNIA PROPOSITION 65 WARNING

Warning about chemicals in engine exhaust and their potential health effects in California.

IMPORTANT SAFETY INSTRUCTIONS

GENERAL OPERATING SAFETY

Essential safety guidelines to follow before and during unit operation.

GAS UNIT SAFETY PRECAUTIONS

Specific safety warnings and precautions for gasoline-powered units.

WHILE OPERATING SAFETY

Safety measures to observe while the unit is in use.

OTHER SAFETY WARNINGS

Additional safety precautions for operation, storage, and maintenance.

SAFETY & INTERNATIONAL SYMBOLS

SYMBOLS AND MEANINGS

Explanation of safety alerts, operational symbols, and international pictographs used in the manual.

KNOW YOUR UNIT

APPLICATIONS

Outlines the primary uses of the trimmer, such as cutting grass and edging.

ASSEMBLY TOOLS REQUIRED

Lists the tools needed for assembling the unit, primarily a screwdriver.

SPECIFICATIONS

TECHNICAL SPECIFICATIONS

Details engine type, displacement, spark plug, fuel/oil ratio, and dimensions.

ASSEMBLY

INSTALLING THE CUTTING HEAD SHIELD

Step-by-step instructions for attaching the safety shield to the cutting head for both models.

INSTALLING AND REMOVING ATTACHMENTS

INSTALLING AN ATTACHMENT

Procedure for connecting accessories using the coupler mechanism.

REMOVING AN ATTACHMENT

Procedure for safely detaching accessories from the coupler.

HANDLE INSTALLATION AND ADJUSTMENT

INSTALLING THE HANDLE

Steps for mounting the handle onto the upper shaft housing.

ADJUSTING THE HANDLE

Instructions for repositioning the handle for comfortable operation.

OIL AND FUEL MIXING INSTRUCTIONS

FUELING THE UNIT

Guidance on safely refueling the unit, including precautions and steps.

STARTING AND STOPPING

STARTING INSTRUCTIONS

Detailed steps for safely starting the 2-cycle gas trimmer engine.

STOPPING INSTRUCTIONS

Procedure for safely shutting down the trimmer engine.

OPERATION

HOLDING THE UNIT

Proper posture and grip for safe and effective operation of the trimmer.

ADJUSTING THE TRIMMING LINE LENGTH

Method for extending trimmer line using the bump head during operation.

TIPS FOR BEST RESULTS

Recommendations for optimizing cutting performance and technique.

OPERATION TECHNIQUES

DECORATIVE TRIMMING

Technique for trimming around objects like trees and fences.

EDGING

Instructions for using the trimmer for edging sidewalks and borders.

MAINTAINING THE TRIMMING LINE

Tips for managing line wear and breakage on hard surfaces.

MAINTENANCE

MAINTENANCE SCHEDULE

Recommended maintenance tasks and their frequencies for optimal unit performance.

REPLACING THE TRIMMING LINE

Step-by-step guide for installing new trimming line into the cutting head.

MAINTENANCE PROCEDURES

REMOVING OLD TRIMMING LINE AND OBSTRUCTIONS

Instructions for clearing debris and old line from the cutting head.

MAINTAINING THE AIR FILTER

Steps for cleaning and oiling the air filter for engine health.

UNIT ADJUSTMENTS AND SPARK PLUG

ADJUSTING THE IDLE SPEED

Procedure for setting the engine idle speed for smooth operation.

MAINTAINING THE SPARK PLUG

Guide for inspecting, cleaning, and gapping the spark plug.

CLEANING AND STORAGE

CLEANING THE UNIT

Instructions for cleaning the exterior of the trimmer unit.

STORAGE GUIDELINES

Procedures for both short-term and long-term storage, including preparation.

TROUBLESHOOTING

COMMON PROBLEMS AND SOLUTIONS

Addresses issues like engine not starting, idling, accelerating, and line feeding problems.

WARRANTY INFORMATION

LIMITED WARRANTY DETAILS

Covers terms, scope, eligibility, and exclusions of the Craftsman product warranty.

WARRANTY EXCLUSIONS AND LIMITATIONS

WARRANTY EXCLUSIONS

Details items and conditions not covered by the limited warranty.

WARRANTY LIMITATIONS

Explains limitations on implied warranties and liability for damages.

REPLACEMENT PARTS AND REPAIR SERVICE

CONTACT INFORMATION

Provides phone number and details for ordering parts or scheduling service.

Related product manuals

Craftsman Weedwacker 172.74536

48 pages

Craftsman WEEDWACKER 316.74556

48 pages

Craftsman Weedwacker 358.799080

16 pages

Craftsman WEEDWACKER 316.795861

32 pages

Craftsman WC215 User Manual

Table of Contents

Questions and Answers:

Craftsman WC215 Specifications

Summary

SAFETY

SPARK ARRESTOR NOTE

CALIFORNIA PROPOSITION 65 WARNING

IMPORTANT SAFETY INSTRUCTIONS

GENERAL OPERATING SAFETY

GAS UNIT SAFETY PRECAUTIONS

WHILE OPERATING SAFETY

OTHER SAFETY WARNINGS

SAFETY & INTERNATIONAL SYMBOLS

SYMBOLS AND MEANINGS

KNOW YOUR UNIT

APPLICATIONS

ASSEMBLY TOOLS REQUIRED

SPECIFICATIONS

TECHNICAL SPECIFICATIONS

ASSEMBLY

INSTALLING THE CUTTING HEAD SHIELD

INSTALLING AND REMOVING ATTACHMENTS

INSTALLING AN ATTACHMENT

REMOVING AN ATTACHMENT

HANDLE INSTALLATION AND ADJUSTMENT

INSTALLING THE HANDLE

ADJUSTING THE HANDLE

OIL AND FUEL MIXING INSTRUCTIONS

FUELING THE UNIT

STARTING AND STOPPING

STARTING INSTRUCTIONS

STOPPING INSTRUCTIONS

OPERATION

HOLDING THE UNIT

ADJUSTING THE TRIMMING LINE LENGTH

TIPS FOR BEST RESULTS

OPERATION TECHNIQUES

DECORATIVE TRIMMING

EDGING

MAINTAINING THE TRIMMING LINE

MAINTENANCE

MAINTENANCE SCHEDULE

REPLACING THE TRIMMING LINE

MAINTENANCE PROCEDURES

REMOVING OLD TRIMMING LINE AND OBSTRUCTIONS

MAINTAINING THE AIR FILTER

UNIT ADJUSTMENTS AND SPARK PLUG

ADJUSTING THE IDLE SPEED

MAINTAINING THE SPARK PLUG

CLEANING AND STORAGE

CLEANING THE UNIT

STORAGE GUIDELINES

TROUBLESHOOTING

COMMON PROBLEMS AND SOLUTIONS

WARRANTY INFORMATION

LIMITED WARRANTY DETAILS

WARRANTY EXCLUSIONS AND LIMITATIONS

WARRANTY EXCLUSIONS

WARRANTY LIMITATIONS

REPLACEMENT PARTS AND REPAIR SERVICE

CONTACT INFORMATION

Related product manuals